I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Dear Support Team, I have downloaded the latest version of VS Code;
I have also installed the latest version of the nRF Connect for VS Code Extension Pack;
The J-Link...
ncs: v3.2.0
chip: nRF54L15
If I set CONFIG_PM_PARTITION_SIZE_MCUBOOT=0x10000 (64K), MCUboot fails to boot, and the error displayed is: 'Protect mcuboot flash failed...
We are not using the NRF5340DK board. According to tests, after initiating an SPI data exchange, the program is delayed in executing the next CS pull-high operation, resulting...
Hi,
I’m trying to finish the first exercise of lesson 1, but when I save it to flash and run the binary, I get this error and I don’t know what’s causing it.
Could someone...
Hello dear community!
Few months ago I bought a NRF52840 from MakerDiary ( https://wiki.makerdiary.com/nrf52840-mdk-usb-dongle/ ) for a personal project arounf Zigbee...
Hi Team,
I am using NCS v2.9.0 and trying to implement a custom Zigbee cluster with custom attributes.
Could you please suggest an example or guide me on how to send...
I'm currently testing the walkie-talkie mode on this development kit, however, when testing it outdoors it only allows a very short connection distance and disconnects. How...
Hi, this question might sound a little silly, but is downloading my device location history from nRF Cloud free of charges? I want to analyze my device's travelling pattern...
Hi there,
I am using an nRF9160DK and looking to get accurate Timing Advance numbers from it and also information on neighbouring cells. I believe in order to get an accurate...
We are using both serial ports running over USB on the nRF54L15DK:
uart20 is LOG, CONSOLE, etc.
uart30 is for our communication (enabled in our overlay)
When we...
Hello,
I am trying to get a custom board working with NOR Flash chip but I am having issues getting the flash chip "ready". I am running the sample application "spi-flash...
Hi!
I've used nrfutil to dfu ble before on a target that just loads and runs a bootloader (for cycle testing).
I'm trying to use it again with a target in the application...
We have a NCS 3.0.2 app + MCU boot with OTA functionality on nRF54L15 (PCA10156 rev 0.9.3)
After upgrading to NCS 3.1.1 it doesn't boot anymore.
I tried with
Key provisioning...
nRF9151 has access port protection enabled by default. I need to debug firmware for nRF9151 produced by a non-secure build. I am trying to follow Figure 120 (Access port unlocking...
Hello,
I have a series of nRF52840 devices that are already connected together in a Thread Network.
My system is composed by one client and multiple servers.
My devices...
