I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello,
I am developing a project with the nRF54L15 and would like to obtain recommendations for specific part numbers of crystals compatible with the reference layout. ...
Hi,the Nordic team
I found that I couldn't set the FeatureMap attribute in the occupancy sensing section within .zap. How can I set it then?
the borad:Nrf54L115
the...
Hello all,
I am working on a project with 2 nrf5340 Audio DK's, and I have been working for a while now on getting myself familiar with the audio application, but I have...
Hi,
I'm trying to run the zephyr/samples/drivers/adc/adc_dt example on the nRF54L15 DK .
I modified the board overlay file zephyr/samples/drivers/adc/adc_dt/boards/nrf54l15dk_nrf54l15_cpuapp...
Description:
I'm having an issue with my nRF52811 custom board where the device won't start BLE advertising after programming, but it works after cycling through GDB monitor...
Hello,
Following the NRF54L Express course I see that PWM duty cycle can be updated from RAM via EasyDMA but I can't see an example of how this can be done anywhere...
I'm moving to 2.9.1 and trying to get mipi working with a st7789 display. I have it working with 2.6.1 without mipi, but can't seem to get it working with mipi on a nrf5340dk...
When i flash i always get the this error: before this i had an another sensor the VL53L0X which worked perfectly.
[0Sensor device not ready! 0:00:00.254,119] <err> VL53L1X...
We are trying to develop a smart controller based on the nRF54L15 that supports a dynamically configurable number of buttons. We want users to be able to select the number...
Hi,
I’m trying to explore the capabilities of DECT NR+ technology using the nRF9151-DK. Are there any recommended external antennas that I would be able to use with this...
Hello,
we are building a custom PCB using the nPM1300. We need a low-noise 1V8 rail for a sensitive analog component and are wondering what the best setup for that would...
I’m working with the CRACEN peripheral on the nRF54L15 and I’m trying to understand the DMA User Tag field used in registers like `CRYPTMSTRDMA.FETCHTAG`.
The documentation...
Hello,
i'm working on a matter sensor on a nRF52840 Dongle and BME280.
The softaware is based on matter/temperature_sensor with config changes to support nRf52840 Dongle...
