I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Dear Sirs,
SDK: NCS version 1.6.0
Board: nrf5340 DK
IDE: SES Nordic Edition V5.50c
Compiled in application core cpuappns
I am a beginner with nrf programming...
Hi all,
we use nRF Connect for Desktop Programmer tool for flashing nRF5340 at production plant. Our Regulatory Affairs & Quality Assurance dept. is asking for a validation...
Sometimes the Power Profiler App does not display the average current and charge values for the Window (see screen capture, below). The values are displayed while the capture...
I'm working on a program using the ble_peripheral/ble_aapp_uart project. While testing the program, it was confirmed that the connection was disconnected after 1 minute 35...
Hi ,
I tried to use the sample code of central and peripheral project "ble_app_hrs_rscs_relay" , to add a new service to connect with light and button peripheral by "lbs_c_init...
Hello,
we are developing a PCB with a nRF52840 in normal power mode. I know that VDD and VDDH have to be shorted in the normal power mode, but due to a layout error we have...
when debugging peripheral_uart sample in ncs1.5.0 used nrf5340dk board , a error produced in function static int bt_init(void)
static int bt_init(void) { int err;
err...
I am trying to use nrfjprog.exe (for the first time) to see if my code is being corrupted on a power fail. It keeps returning an error that I can find documentation on.
...
Hi,
We bought smart watch from company xyz. Watch is running using Nrf52840 and supports buttonless DFU. we are customizing the smart watch firmware as per our requirements...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
My device is a peripheral. I want to connect with two smartphones. At that time, I want to connect under the following...
Hi, Could you provide source code of nRF Sniffer for Bluetooth LE firmware?
https://www.nordicsemi.com/Software-and-tools/Development-Tools/nRF-Sniffer-for-Bluetooth-LE...
Hey Guys :) have a MQTT code that publishes certain AT commands, It works for all cases except Mutlicell 'NCELLMEAS' command. Any help would be appreciated.
[This Works...
Hello
I am using sdk17 and st7735(GFX) drivers.
I am simply printing the sensor value on the display. Initially, it works well, but after a few minutes, the screen is...
