Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi All,
I am developing product using nRF52840 and SDK nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71.
This product is basically, using the Thermostat cluster and Zigbee...
hi
i am working on nrf52dk. my dfu code is working first time . second time when i try to update code with android app. it gets stuck on starting bootloader.
I am trying to compile and upload https_client onto my Thingy91. I am compiling it in bash using 'west build -b thingy91_nrf9160ns --pristine -- -DCONFIG_BOOTLOADER_MCUBOOT...
Hi there
I am trying to write a simple code that will flash turn on an LED fro one I/O pine of the nrf24le1 in response to an input from another I/O pin of the nrf24le1...
Is it possible to install the development environment on a PC that is not connected to the internet.
I need to be able to download all the files from a PC connected to the...
Hello.
I need to add an output gpio to the dts file, I modified the board.dts file, inserting these lines in the leds section
res: res_ {
gpios = <& gpio0 17 GPIO_ACTIVE_LOW...
To flash a new firmware I always do the same thing.
Open NRF Connect
Open Bluetooth Low Energy
Click: Start Scanning
Click: Sort by signal strength
Choose the...
Hi,
As well know, nRF52832 have more then one SPI and TWI interface.
How can I use SPI and TWI interface in the same program? for example, use SPI-0 and TWI-1.
Thank...
I don't understand how the guide gets to the Open IDE button. I used the automated installer and it did not appear for me. The guide did not provide any instructions on how...
I see that in the 6.20.14.20 RXADDRESSES in Reference Manual I can enable multiple addresses in the same time, so is it possible for nrf52840 to listen on several addresses...
SENT protocol uses a 1-wire interface to transfer data using time intervals. To receive data you simply measure the time between pulses on the wire. The transmitter never...
When I use the BLE mouse example in the nRF5 SDK (17.0.2), it works on iOS (14). However, the report is divided into 3 parts. I would like to combine the mouse buttons, X...
We are developing a controller for an Electric vehicle charging station. Already developed and successfully running the firmware on ESP32 for which we had used platformio...
I am using this tutorial to write a custom service and I got to a point to add custom characteristics and got a few questions:
- I don't seem to find any characteristic...
