Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hey All,
Last month a network provider had some internal issues which rapidly started rejecting our devices with several EMM registration issues, however due to not seeing...
Hello All,
We have developed a Zigbee End Node device for which we would like to make a radio test.
we are using nRF connect SDK 2.0.0, please note the reason we use the...
Hello Nordic Team,
I’m currently working with the nRF5340-DK and nRF Connect SDK (v2.6) using VS Code . I’ve been testing OTA firmware update processes using MCUboot and...
Hello
I need help, I have a problem implementing ppi gpiote and spim. The ADC I use is mcp3562 which sends via the irq pin when the data is ready. I need to work in continuous...
I used Nordic52480 DK(bulb) as DUT to run Matter Certification case TC-DGGEN-2.1 .
Steps:
1. setup OTBR on Pi4：./certification-tool/backend/test_collections/matter/scripts...
Hello I have an nRF52840 board with a 2 MB external flash I'm using SDK 2.6.2 I'd like to configure the mcuboot_secondary partition to be on the external flash
Here is my...
Hi,
I'm about to develop a custom board with nRF52840 IC. For a first test I need an external antenna. I modified a dongle for a first proof of concept. I removed the antenna...
Windows 11, VSCode, NCS v2.3.0
Hi, I have a well-working application that I would like to build ztests for.
I'm reading about how to do that on the test framework page...
I often see the following warning when requesting a GNSS location: "<wrn> location: PSM is configured, but modem did not enter PSM in 2 minutes. Starting GNSS anyway." - what...
Hi everyone,
We’re currently using the nRF9160 module with JIO Nb-IoT SIMs in our devices. Could anyone clarify if any specific actions are needed in the firmware for...
I have an nRF54l15-PDK dev board (brand new):
I did the following commands with the SDK v3.0.2. Building and Flashing went fine:
to build:
west build -b nrf54l15dk...
During development we noticed that current measurements coming from npm1300 appear to be much higher than expected despite the results not matching what we were seeing on...
Hello, I have a question about the headphone jack output on the nRF5340 Audio DK.
In past DevZone threads, it has been stated that “the headphone output through the CS47L63...
