I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
I am trying to replace such a platform and was hoping to use nRF9151 as a starting point.
Is such a platform possible at all with Nordic/Zephyr ?
I have an old 9160 dev...
I am trying to use Edge Impulse ML models on my custom board. I have built my model on EI and downloaded it locally. I followed the sample wrapper code to use my own model...
Hi, I am devolping a sensor system where I am in need of a Tri state GPIO solution
Currently using the NRF54l15DK with all the latest software versions (3.11, etc.), developing...
I am trying trilateration for indoor positioning system with nrf54l15 , using 3 initiators and a reflector I was not able to switch between initiators and also one of the...
Product is a zigbee router.
Use nrf connect sdk 2.4, update it is not an option.
The zigbee join work fine most of zb3.0 coordinator, BUT with an old coordinator it failed...
Hi all,
I'm using aws iot lib and last will topic feature, everuthing works but I have a question, in prj.conf I set my topic with
Is it possible to build this last...
Hello Nordic Team,
We have developed a custom PCB using nRF9151 and nPM1300 . In our setup, sometimes the PMIC powers up and works correctly, but other times it does not...
Hello, I am using Nordic chip 82832 with sdk 17.1.0 and SoftDevice s132. I am facing an issue where a specific requirement requires my advertisement interval to be specifically...
Hello,
we would like to use the LPCOMP on the nRF54LM20A, but there's some confusion on which GPIO domain can be used.
According to the overview block diagram , LPCOMP...
Hello,
I'm working on a custom Zigbee End Device application where I want do some modification of the device announcement message. I've used NXP's Freescale Beestack Zigbee...
In Nora B-206(nrf54l15) not able to use port 1 pins 2,3 (P1.02/NFC1 P1.03/NFC2) as normal GPIO. TRIED :
& nfct {
status = "disabled" ; // Disable NFC to free P1.03 for...
Hi,
I'm using a custom code I developed to save all console logs to an SD card based on the Zephyr architecture. I originally developed it for the Thingy:52 and have also...
Under the old `nrfjprog`, it was possible to check whether the modem firmware matched a particular release by running `nrfjprog --verify mfw.zip` (see )
This is no longer...
Hi Nordic support:
We previously submitted a case about OTA testing in CMW500 connection mode. Following is that case:
We tried OTA testing with the CMW500 connection...
Hi everyone,
I’m starting a new project using the nRF54L15 MCU . I’ve worked with the nRF52840 and nRF52832 before, but this is my first time with the nRF54 series.
Due...
