hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
I want to write numbers in my flash memory so I used this function "nrf_nvmc_write_words" but in it couldn't save float numbers in my flash memory
it is like that in nrf_nvmc...
Hello All,
I am using nrf52840 in my project. So basically the architecture is the sensor devices(ble peripheral) get connected to the central module(ble central). Now I...
hi support team,
customer is finding that 832 erase page takes more time than normal conditions, that is when the temperature is -20, erase speed is much slow.
as our...
Hi all,
I am confused about nrf52832 Tx/Rx max current. I am using PPKII measure the power current of NRF52 DK PCA10040 , As the following screen shot, :
In DC/DC mode...
Hi,
I'm working on a custom board based on PCA10100, nrf52833 but it seems to be stuck at the function "lfclk_spinwait".
my custom board does not have an external LFCLK...
Hello,
For my application I have a need to buffer data for, say, 8 GPIO pin outputs and continuously generate those buffered outputs in parallel on the GPIO pins. I have...
Hi,
According to the BLE core specification, a host can communicate with multiple controllers via HCI. I want to confirm whether zephyr's BLE stack supports the feature...
Hello,
I am working on a project using the nRF5340. I will eventually be supporting OTA DFU for both cores so I need to be able to statically define the partitions for both...
Hello, I am porting to nRF5340 from nRF52833. Previously, we were using sdk17.0.2 for nRF52833 and we were able to successfully implement encryption algorithm AES-CTR-128...
Hi,
I have a NRF52840-DK (400236). I was using it for the development. It was working perfectly.
Suddenly the issue arises the power section is heating up.
I am powering...
Hi,
I am running the standard Grove LCD code, as below but am getting an error, " Grove LCD: Device not ready.'
the code is
my overlay file is
and my proj...
Hello,
we have a set of router devices already on the market: each of them was developed using 4.0 stack.
now we're aligning the stack to the 4.2 version observing a very...
Hi!
I've followed the app timer example to implement app timers in my project. My project is low power consumption oriented. When I use a repeated timer, power consumption...
Hello,
We are integrating the nordic sdk for DFU on our own application on Android and iOS.
We need to know al the possible error codes that the sdk can sent but we...
