hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
HI,
We are looking to multiplex a few I/O on the NRF52840 to save pin count on a header. If D+ or D- get driven when VBUS is unpowered, will that damage the NRF52840? Or...
Hi there,
I think that I am seeing the repercussions of errata item 136 in my application. I abruptly turn on/off power several times to my board, and every once in a while...
Hi,
On my bl653_dvk board, I am running the ADC example. It functions properly. I have a few questions about this:
1. How to determine which clock is being used by the...
Hi everyone,
I want to send large data with https protocol.
I edited the https_client sample split the data and looped send() for sending the large data.
But when...
I am working through the https_client example with the nRF9160 and I noticed that when Connection: close is not included, the connection doesn't close, but if I attempt to...
Hi,
I'm sending values over ble. On the client side I opened an serial monitor. Everything seems fine. The values are received in the right way.
But when I try to read...
Hi,
I have previously used the ESP8266 WiFi module and it has worked great. Since I have updated to the latest SDK, I am now seeing problems. I'm guessing something has...
I am currently working on enabling and transmitting/receiving data using TWIM on my nRF52810 development kit. The documentation states that in order to enable TWIM I need...
Hello,
I told my students to set up an SPI bus with several peripherals. We found nice development boards with a screen and a card reader sharing MISO,MOSI,CLK and one CS...
Device: nRF52840 Softdevice: 140 SDK: 17.1.0
I'm trying to develop a custom bootloader that will determine which of two images (A or B) to jump to. The memory map that I...
I noticed that if I set options = BT_LE_ADV_OPT_NONE in bt_le_adv_param I get a random address at each bootup and if I set it to BT_LE_ADV_OPT_USE_IDENTITY I get always the...
Hello,
I'm currently working with ISP2053 which is the nRF5340-based module.
The system, as the specific GPIO pin detects a low-to-high event, gets data from another...
Hello guys,
I'm trying to run uart example from https://github.com/andenore/NordicSnippets/blob/master/examples/uart/main.c extended by interrupts call after transmission...
Hi.
I cannot build a ble_app_uart Nordic example that I was able to build flawlessly three years ago and later. I wonder if anybody could give me a clue on what's going...
