hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
I installed the nRF Toolbox on my phone and received data through BLE uart. However, how can I download/save this data on my phone? For example, I send the temperature to...
Hi,
I'm trying to send an data array over ble nus.
This didn't work.
I'm also getting this warning.
I'm doing something wrong, but I don't know what. Do I also...
Hello,
I am making a Firmware for the FCC certification, I must emit at 3 different frequency, 2404MHz (ch37), 2440MHz (ch17) and 2480MHz (ch39) on a nrf52832.
I unfortunately...
Hello,
I have installed the NCS toolchain using the Toolchain Manager app. I am using toolchain version 2.0.0. Here is the error I get when running `west status` :
Same...
I received Thingy:53 and tested it by following the Getting started with Thingy:53 SDK documentation.
The problem arises from the sentence below.
Getting started with...
Hello,
I'm using the LTE Link Monitor v2.0.1 with the nrf9160dk_serial_lte_modem_2022-06-02_880c82db application on a nRF9160.
I'm able to establish the connexion and...
I saw a news report on Nordic's official website that Nordic's NB products have passed the certification of Chinatelecom. I wonder if they have passed the certification of...
Is there a way to add an offset to the nRF5340's reported RSSI to compensate for any front end loss or gain the design might have? This is to get to an RSSI value at the antenna...
Hi,
I'm using HID mouse example in SDK17.02.
After downloaded soft device and the application, I add the device in my pc blue tooth. I can see the battery level normally...
Hi,
I'm looking for a product Bluetooth 5.2 Radio System-on-Chip (SoC) which is of automotive type, and their operating temperature ranges are (-40 to +125)
I'm working on Electronic Shelf Label project using Feather nRF52 with Raspberry pi for server connection. I need to Adafruit Feather nRF52 to receive data from raspberry...
Hi Sir,
We follow this link to test the NIDD, but I'm not sure whether it is successful.
1. Can we know the NIDD link successful or not from the log? What can we see if...
Hello, We are using the serial LTE modem on the nrf connect sdk v1.9.1. We are trying to receive a big message on a topic we have subscribe to, but the serial LTE modem crash...
Hi, I'm using SDK17.02 on nRF52810,and I have enabled AIN6 reading the voltage of battery successfully.
Now I need to read another voltage outside at the same time, so what...
I are working with the asset tracker v2 app under the nrf connect SDK v2.0.0. We are using the nrf9160DK as nRF9160DK_nrf9160_ns. The precompiled asset_tracker_V2 .hex file...
