hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Topology:
Raspberry Pi A Raspberry Pi B
|(USB connect) |(USB connect)
nRF52840 dongle A )))) Thread (((( nRF52840 dongle B
Software:
nrf52840-dongle: ot-rcp.hex...
In the online power profiler for nRF52832, when I look at the advertising (Tx/Rx) power consumption I see that if I set the Tx payload to 0 bytes the Tx time modeled is 128us...
Hello,
In my project i want two use two UART as off now i am using app_ble_uart example since by default 6,8 is tx and rx pins respectively. so overall application of my...
Hello everyone
I am working on nRF52DK devkit. I want to check the SPI waveform. Actually I want to interface waveshare e-paper display (1.54 inch) For that i used GFX...
On the Thingy 91, the default configuration allocates a lot of flash space to several mcuboot partitions, leaving only 380kb for the app.
I need more space for the app,...
I have a custom application that works well for my nRF52832 device, but my team is moving on to an nRF52840 chip. Long ago, I deleted the directories that were not /pca10040...
I am using the UART multi-central example (from GITHUB) and connecting multuple peripherlas each streaming data at 38K
The multi-central is gathering the data from the various...
Hello, I'm having the same issue as in this thread but the proposed solutions doesn't work for me. This is the output from the terminal:
*** Booting Zephyr OS build v2.7...
Hello, I tried to upload a simple blink sketch from pca10040 which works for nrf52832 to an nrf52810. But it didn't work. Then I tried pca10040e. It worked for nrf52810. ...
I accidentally clicked verified answer while trying to edit the page.
https://devzone.nordicsemi.com/f/nordic-q-a/87116/apply-the-heartbeat-publication-and-subscription...
I want to be able to send the "AT%" type of Nordic proprietary commands to the modem (and read the response back) via firmware on the nRF9160. I know about the
nrf_modem_at_cmd...
Currently I have been able to advertise and connect through debug app using nRF52 DK. My target is:
1. After the link is lost the bluetooth gets disconnected and at this...
I have been using Segger Embedded Studio to develop in and recently switched to use VS Code with NCS. It was always very useful to use Segger's watch window with the real...
Hi All,
I want to add pairing and binding functions to the blinky project.
But nothing happens when I connect.
Please help me,thank you.
Here is my project =>
...
