Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have an application where I need multiple AWS_IOT_SEC_TAG to connect to different AWS IoT servers, including the nRF Cloud server. How can I do that with the CONFIG_AWS_IOT_SEC_TAG...
Hi all
Im trying to implement on bluetooth communication between two nrf52840 DK, I have made a custom uuid service on peripherial. Now I have to do GATT discovery service...
Hello! We are developing a schematic for our device and trying to correctly assign GPIOs for different peripherals. There is the Cross power-domain use section in the documentation...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hello at all, I try to compile the example peripheral_uart for the nrf54L15-DK. The goal is to compile without west. My directory structure:
where I copied everything from...
Hello,
I am developing on the NRF54L15 DK board, using the SDK v3.1.0 and v3.1.0 toolchain. I am trying to use the macro NRF_RADIO_INT_RSSIEND_MASK, but RADIO_INTENSET_RSSIEND_Msk...
I'm using the NRF5340. When I open a standard example project located in the directory: nrf\samples\bluetooth\peripheral_uart (the well-known Bluetooth data transparent transmission...
I am experiencing system resets caused by the WDT (Watchdog Timer) while using the nrf52832。
This is my WDT configuration code：
void system_wdt_init(void) { uint32_t err_code...
my sdkconfig.h related to fds
my entire code error: my entire sdkconfig
i have tried changing no of pages , using nvmc driver, but i am getting the same error steps...
HI，
I am using the nRF54L15 with SDK v3.0.0. I am currently using Timer20 for a counting function. My original power consumption was 4.6 μA when Timer20 was not enabled...
Dear Nordic DevZone,
I have a question which is quite noobish but I want to make sure I am using the right tools for the job. My setup looks like this I have a raspberry...
After gradually increasing up to ncs 3.1.0, the following issue occured: After:
LOG_INF ( "Initializing modem library" );
err = nrf_modem_lib_init ();
if ( err ) ...
Hi [Nordic Support Team / Developer Team],
I would like to confirm why the nRF54L15DK is not listed among the supported development kits for the Bluetooth: Peripheral ANCS...
I tried two different applications in BT fundamentals, the solution to Lesson 3, Exercise 1 and the solution to Lesson 4, Exercise 1. Both show "Advertising successfully started...
