I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hello, I have done customized board using nRF52832 and when I try to flash code using nRF52 DK(Jtag) it is showing following error. could not fetch memory size of target devkit...
Hey all - I'm new and trying to connect Thingy91 to nRF Connect V3.6.1 for the first time. When I open the Programmer app I only see "No devices available" in the drop down...
Hi,
I'm trying to follow the NCS tutorial in: https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/getting-started/posts/nrf-connect-sdk-tutorial---part-1-ncs...
Hi,
we are developing a custom BLE communication. For this we are using:
- nRF5_SDK_17.0.2_d674dde - s332 - based on BLE NUS UART example
Everything works fine, until...
I'm trying to open a NCS project in SES but I'm getting error 1 from create_nordic_project.py. NCS 1.5.0 installed with toolchain manager on macOS 11.2.2
The error in SES...
Hi,
I am following a client case that they have issue on accessing SD card via SPI port.
I used the sample project fat_fs on nrf9160_pca10090 DK and used SPI_3 to access...
nRF9160 DK schematic sheet 2 missing pin names for WP and HOLD of nRF91_EXT_MEM in the On-board interface (far right page 2)
could someone post what nRF9160 pins are used...
Hi,
I have written one application with logging disabled to save power.
However, when I tried to debug the code with Ozone, during startup, it raises BusFault exception...
Hi,
I am currently working on generating a dfu over serial uart by testing with the ble_app_blinky example given in the SDK 15.2.0. Currently the ble_app_blinky hex file...
Hi ! Using nRF52840 whith SD140 as central and 6 link count I research :
changing the NRF_SDH_BLE_GAP_EVENT_LENGTH from 6 to 2 does not change "Window size" on CONNECT_REQ...
Hi,
I messed up my SES project and now the debugging session doesn´t start and the debugger does some weird stuff and doesn´t execute my application.
I also tested if...
Hi,
I am using the DFU example given in the SDK15.2.0 to try and update the application on my NRF52840. Currently, I have been able to update the application to run the...
I use many SEGGER_RTT_WriteString and SEGGER_RTT_printf sprinkled throughout my code which was very helpful for debugging and monitoring, however, we're getting close to releasing...
I have attempted to update the firmware on the Nordic Thingy:91 via usb connection to my laptop running CentOS 8, however, finding great difficulty updating the firmware through...
My stm32 (as a master) uses SPI to communicate with nrf52840 (as a slave) When my nrf52840 wants to send data to stm32, it will pull a GPIO to let stm32 generate a GPIO interrupt...
