We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Hello, Guys. Using the function ble_nus_string_send, I've sent sensor values to my mobile phone. However, the data received came from an unknown character being broken. I...
Hello,
I use aws_fota as starting point on a mobile device with MQTT reporting.
What is the best way to manage loss of connection (how to know and how to cleanly rebuild...
Hello Nordic support
We want to add a function to monitor the RSSI of the other party's mobile phone at the time of Connetion instead of advertising. Is it possible...
Hello Nordic Support,
I have modified the USB MSC example to use SD card and have also initialized UART port. Basically, what I'm trying to achieve is to write data received...
Hi,
Question 1: Why nRF52832 not supporting Thread? Is it because Memory? Hardware?
Question 2: Can you advise what is the advantages or applications to use BLE+Thread...
Hi,
I'm sorry but i cannot find in the discussion the definition of this structure NRF_SPIM_Type
it is not defined in nrf_spim.h
typedef struct { NRF_SPIM_Type * p_reg;...
Hi,
We are looking for an industrial solution to program our NRF52832 on a custom board, until now we are using the programming chip directly from the NRF52DK, it works...
My custom board with NRF52810 is done and I'm now trying to get some examples working. I am adapting blinky_s132 in SES. To do this I edited the project options including...
i'm new to this board can you find some course for this board
from scratch the courses will be very helpful
just the video tutorials are very advanced
the documentations...
Hi folks,
I am working on ble_app_uart example program nRF52 SDK 15.2 Verion , in this case i am writing the data in flash for future use , Now i am to get the specific...
Hi Team,
We are using nRF52840 DK with sensors. We developed a custom code that is working fine. But the issue is current consumption. Showing below the readings.
The...
I have taken the code found here:
https://github.com/bjornspockeli/custom_ble_service_example
and modified it so that the custom characteristic is located in user memory...
Hi,
Good day!
I tried to add the RTC2 driver to our application and i keep getting this compiler error message (using sdk16.0).
Here is my sdk_config.h. Not sure why...
Hi
I'm planning to connect three different BLE peripheral like Heart-rate sensors, Health Thermometer, and Blood Pressure to a Central BLE device.
I'm using a small customized...
Hello
What is the specified max current on the supply pins for nRF52840?
The GPIO pins are specified to source max 14mA in 'high drive' mode:
How many of these pins...
