HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
I want to know how to adjust the TX RX setting for the nRF52833 DK connected to the nRF21540 EK shield. I have already added -DSHIELD="nrf21540ek" to the build configuration...
Hello.
I am trying to repeat the functionality of the project that is shown in this video https://www.youtube.com/watch?v=fCU8x-pmtqU&list=PLx_tBuQ_KSqG-leiJDfOKf_ZmCqHnbi4r&index...
We are using SDK v2.6.1 for our application, along with the Fanstel module WT02C40C.
Internet connectivity is provided to the WT02C40C module via a hotspot, with CONFIG_STA_KEY_MGMT_WPA2...
The "nRF Command Line Tools" page, https://www.nordicsemi.com/Products/Development-tools/nrf-command-line-tools says " Important: The nRF Command Line Tools is in the process...
I want to interface 3 custom made heater boards to nrf5340dk. Where the simple task is to toggle gpio's to Turn ON & OFF the heater board. Now, we are using P 0.01, 0.02 &...
Hello, I am considering the prospect of using channel sounding as opposed to UWB for indoor asset tracking. I can understand, that the main limitation with that would be,...
Hi There:
I used the nRF7002 DK to evaluate its WiFi throughput performance.
The test environment is below:
1. nRF7002 DK
2. NCS version: 2.5.0
3. Sample application...
Hello Everyone,
I have configured SPI1 at 1MHz, to receive data with a sensor. Basically i am reading data from a sensor device. So calling spi_transceive_dt() with 4...
The current specifications (v0.8) for the nRF54L series of parts provide very little information about the input impedance of the SAADC peripheral. There are no values specified...
hey i am using a custom nrf52840 board and i keep my device on by setting a gpio pin high and device turns off as soon as it sets to low .
during ota update when the bootloader...
Hi,
I have a firmware project that was originally developed for an nRF52833. It successfully mounts LittleFS on 3 partitions in external flash. For the nRF52833 I was simply...
Dear Devzone!
I am trying to add AES-128 decryption support for secure DFU with cc310_bl backend. However when I call nrf_crypto_aes_update it never returns. Examining the...
Hi all,
I started encountering the error shown in the attached screenshot.
From the this PR , it seems the issue is new and that the PR is aimed at resolving it. However...
Hi,
I'm developing a BLE Central using a nRF52840 DK. My project goal is to analyze the quality and the robustness of a peripheral's BLE connection.
For some parts of...
