Has anyone used a graphics library like emWin or TouchGfx on nRF52?
www.segger.com/emwin.html
http://touchgfx.com/en/
I do not see any posts on either forums or here...
Hello,
We can not convert Altium File to DipTrace or Eagle File. We need those files asap. I'd be thankful if you could help me in that issue.
Thank you
We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to protect the programme and data in the flash memory from being rewritten during shipment.
I thought that I could set the NVMC register, CONFIG, to read-only, so...
today in the morning I can connect this web site via chrome.
but I cannot connect this web site few hours later with banned my ip page.
I don't understand.
my system...
I am working on a project that requires serial DFU without flow control using nRF SDK 17.1.0 running on the nRF52840 without the soft device as I don't need BLE for this application...
We are investigating the use of the Soft Device Controller as an alternative to a Soft Device for our production product. Using our BLE stack we have successfully completed...
I'm using SDK 17 with the nRF52840-DK.
As a starting point for my application, I'm using the .../examples/ble_peripheral/ble_app_hrs_freertos project since shows the proper...
Hello, I would like to make a follower robot. For this, I wanted to use the AoA to locate my phone and thus determine the direction in which the robot should go.
I'm really...
Hello,
I am working with a nRF5340 and need to use both CDC and mass storage on SD Card. I started my application based on the CDC example and it has worked fine.
Now...
Hello,
NCS1.9.1, VSCode, nRF52840,
from link UART Driver – Nordic Developer Academy (nordicsemi.com)
uart can't to receive data continuously,
receiving evt->data.rx...
Hello,
I am working on nRF52840 DK and dongle. I am trying to implement a firmware that can scan device and send command through NUS. So I use ble_app_interactive example...
So, this could just be an odd coincidence, but I'm stuck.
I had a project working using standard advertising. You connect, pair, and then the client (nRF Connect on Android...
Hi! I'm trying to encrypt some data using ECC 256 but I have some issues:
-I found a code ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/nrf/samples/crypto...
Hello! I'm trying to use a custom SPM using this guide: https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/using-a-custom-secure-partition-manager...
I closed the previous discussion by mistake: https://devzone.nordicsemi.com/f/nordic-q-a/83067/nrf9160-board-for-qr-code-project?ReplySortBy=CreatedDate&ReplySortOrder=Ascending...
Hi there
The project that I am focusing on was really time-critical, so I'm wondering whether we could disable Link Layer ACKs in nRF Connect SDK (i.e. Zephyr) ? If not...
We have been looking at InsightSIPs AoA Demo kit ( https://www.insightsip.com/products/bluetooth-smart-modules/isp1907 ) and are trying to understand the communication protocol...
