We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Hello Devzone Community,
I am facing a run time, peripheral or sensor initialization error in a Zephyr based app, built using sdk-nrf v1.6.1, and its corresponding Zephyr...
My Zephyr based application is buildable and working fine. I followed this tutorial, trying to enable bluetooth OTA for my app: Add DFU support to your application - Software...
SDK Environment: nRF Connect SDK v1.8.0 Target: Decawave DWM1001-DEV. This uses the nRF52832
I used \ncs\v1.8.0\bootloader\mcuboot\samples\zephyr\hello-world as a starting...
Hello,
We have a battery-powered product that currently uses the NRF52832. It is a very low power space-constrained application, so we always evaluate any potential current...
Hello,
I have set my softdevice s132v3 with SDK12.2 and nrf52832 to use connection event length extension and data length extende with connection parameters as shown below...
Two Factor Authentification is enabled for my primary account (I had to create a second one to ask question).
Something has gone wrong with setting up two factor authentification...
I wanted to implement a time sync feature on nRF-52840 DK. I took a reference from this example, but there were certain things unclear to me.
Can somebody explain to me...
Hello. I am developing a central operation using nrf52832 (S132 v7.0.1, SDK v17.0.0).
There is a numeric comparison as an authentication method, can I do it with sdk17.0...
Hello,
I'm new with Nordic products, and I'm trying to use my New dev kit nrf5340 DK.
The request today is about my code, I implemented my code in the DK, and now I want...
i have nrf52832 and softdevice s132. i want to calculate throughput. i tried running ble_att_mtu_thorughput example and read https://www.novelbits.io/bluetooth-5-speed-maximum...
Hi,
when debugging BTmesh (with MPSL) breakpoints trigger an assert. This is listed in the known issues of the nrfConnectVScode page:
https://nrfconnect.github.io/vscode...
Hello, i'm trying to flash a code in my module nrf52805 thx to my Dk nrf52840. i have this error I followed the instructions here: https://devzone.nordicsemi.com/guides/short...
Hello,
I want to build a configuration where MCU Boot secondary partition is in the external flash and QSPI data encryption is turned on.
I modified the nrf_qspi_nor...
Dear, I want to interface nRF5340 to normal 16x2 Alphanumeric LCD running on 5 Volt. Are the Port pins of nRF5340 5 Volt compatible when nRF is running with 3.3 Volt supply...
Hello,
After succesfully configuring the W5500 driver using Zephyr, I am trying a few examples in the given samples (socket echo). I am unable to send or receive / ping...
