I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi Support Team
I installed the NCS V3.1.0 just now. But there was an issue of west: unknown command "build" for the NCS V3.1.0 when I built a sample. Many thanks.
Hi,
I'd like to raise this issue I am having with the v3.0.1 sdk wherein the final build stages I get the message attached
I am using the Lesson 9 exercise 5 sample...
I am trying both v3.0.0 and v3.0.2 SDK; the board I am using is the nRF9160DK, version 1.1.0. There are 4 scenarios:
1) Run on Linux (minicom or Serial Terminal) following...
Hi Support Team
Our product have a CD 4kv and AD 8kv ESD test, but the samples reset on AD 8kv close to the USB, the reset register show it is nRESET PIN reset.
add an...
I'm having several problems with the Intermediate course, L2_e2. In Step 3 it says that there is 'a bug in coredump_gdbserver.py that causes a crash if building with optimized...
I need to use a nrfx timer in order for some GPIO timing, but can't get past the simple examples declaring an instance. For testing I'm just using the 54L15DK.
I was using...
Hi,
I would like to create a UART on the nRF54L15 DK, but currently it seems that only the pins bound to CONFIG_UART_CONSOLE (P1.04 / P1.05) are working as below Output...
HI there,
I like to configure and use the COEX Interface with the COEX Pins for DECT-NR+
on a nrf9151DK Board: https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr...
I am trying to compile my custom BLE application into Babblesim using the nrf5340bsim/nrf5340/cpuapp board in nRF Connect SDK v3.1.0. The application uses PSA Cryptography...
I wrote some firmware that I got working with the Nordic nRF52840 Dongle. It acts as a USB device, you can see under the device manager on a computer when you plug it in....
Hi,
I am working with an nRF52833 using the SoftDevice Controller in nRF Connect SDK 3.1.0, and I have a question about LE Coded PHY (long range).
I understand that...
I am using the nRF Connect SDK V2.9 on my Ubuntu 24.04, along with VS Code, as recommended by Nordic for the nRF52 DK. However, whenever I try to create a new project by copying...
Hi all,
I am using nrf52833 on a fanstel module BM833 with printed antenna. I am on NCS with Zephyr and my application is based on the nrf_dm example. Currently I can get...
I'm attempting to evaluate XIP (NCS 3.0.0) on the nRF53 with a mx25u256 flash chip. I'm placing a simple test function in external flash:
#define XIP_TEST_INC ( 100 )...
Hello, I am using the nRF Connect SDK v2.9.0. While working on the nRF52840 board, I used the library zephyr/crypto/crypto.h to perform AES/ECB encryption.
Part of the code...
