Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hello,
I want to test nRF21540 EK with a nRF5340 DK.
I am using ncs 2.7 , and don't want to use sys build . I want to use child image/ hci_ipc .
I modified ncs/zephyr...
We have devices that have low signal so they have to reconnect to AWS a lot. We have a watchdog timer with a 100s timeout that we feed every 10 seconds in the control loop...
Hello everyone!
I am having trouble with my current setup and I would like to ask you for your advice.
I am developing a central station featuring nRF5340+nRF7002. This...
I generated an overlay file with the following info:
and there is my main.c file:
However, when I tried to debug my code to understand what was wrong, I got the...
Hi,
I am using nrf52840 and implemented shell interface. I have testing it over uart and uart over usb. At any given moment it can be enabled over 1 interface in device...
In this exercise the PWM terminology is used incorrectly, confusing the pwm pulse width (nsecs) and duty cycle (percentage). I know the difference from 40+ years of designing...
Hi,
I am new to nrf and have started working with nrf5340 audio dk board. I am using VS Code for programming and the SDK version used is v2.6.1.
I tested the board with...
Is my following operation, first output high, and then configure as input, and then in the output low, this time in the output low here nrf_gpio_cfg_output(IO_PIN_C[j]); This...
1. Setting the IWindow value smaller than Interval will save power.
2. Setting the Interval and Window values to the same will increase the chances of scanning and being...
Hi,I have been using nrf5340 audio DK Board to access the I2S .I am using SPH0645 mic with that i need to get mic data .I am getting mic data continuously but sure that I...
Hi,
we have npm1300 device on our customized board,
without using any of the regulators, LEDs are not connected.
Gpio 0 and Gpio 4 is connected to main MCU.
when activating...
if you see over here data out line is green and prepuol color is data in line first we are sending the 9F so that it will give the manufacture id like this ef and 40 and 0x16...
Hello Support-Team! We are designing a system, where we need to maintain some settings using shell commands (we plan to develop our own set of customised commands). Our platform...
Hi !
Regarding the dfu upgrade service of thingy52, I would like to ask if it is possible to use some Bluetooth devices (such as laird's bl654) to make thingy52 enter dfu...
