I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
I am having very limited knowledge in flashing devices, infact this is the first time I was doing it, pls conider
Step 1: I bough PCA10040 and installed nRFGo software in...
I have found multiple PDFs indicating the lay-out on the nRF52-DK. However, none of them tell me anything about the size of the kit. Does anyone have a PCB lay-out with at...
Using the latest SDK and following example multiprotocol/ble_app_gzl.
I try to add a vendor specific UUID and get error 4. Which means, not enough room in some table? Whose...
Hi,
I hope this is the appropriate forum for this question. I've also asked this on the developer forum on thisisant.com, but received no answer there.
We are using...
Hi all,
I have a custom board with 3 LED's and one button. I have created a custom_board.h file:
#define LEDS_NUMBER 3
#define LED_START 22
#define LED_1 22
#define...
I wanna build project nRF51822 using ADXL345 for accelerometer sensor that program using eclipse or keil. can you teach me how to build using nRF51822 SDK version 6 or higher...
Hi,
I'd just start developping with the nRF52832 and I would like to communicate with a sensor using the I2C protocol. Has I am a stranger with the nordic uC, I would like...
Hi guys, me again.
I was very confused with my current process on developing with nrf chip now... so I would like to post my develop step and some problems I had so maybe...
I am using ATT MTU throughput example and I noticed that using CLI (calling cli_start) causes the main while(1) loop forever. In other words, wait_for_event does not block...
I just received the Nordic nRF52-DK, and am unable to do anything with it as my laptop does not recognize when it is connected. I do not have the original cable as I did not...
Hi!
I have AD5611 DAC connected to nRF51822 by SPI.
In DAC datasheet we need to send data by MSB first order.
Data packet is 16 bit length.
I feel variable uint16_t...
Hello,
I use the pca10040 and the problem is in 14.0 eaxmple ,when I push the button switch the protocol mode like : ble->gzll->ble and then I find the example loop into...
Hello,
based on the saadc example of SDK 11 I am trying to change the code to use the SAADC's local timer to sample the input given number of times (10 times for the below...
Hi,
well I struggle with another problem right now.
In case of some errors, I use 'sd_nvic_SystemReset' to reset the system.
But the WDT is used in the application. Thus...
