Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
1， The SDK is nRF5_SDK_14.2.0_17b948a;
2, running the usbd_audio project; It don't control the volume by 52840;
3, Can you help me how to adding the volume control in...
We tried two build options:
1. thread version 1.1 with
# Set OpenThread NCP architecture CONFIG_OPENTHREAD_COPROCESSOR=y CONFIG_OPENTHREAD_COPROCESSOR_RCP=y
CONFIG_OPENTHREAD_THREAD_VERSION_1_1...
Hello
I'm using sdk v17.0.2 and I'm going to program using nrf52840 dongle.
I used nrf52DK because I didn't have nrf52840DK. And I'm going to upload the source code that...
Hi!
I am running Zephyr sample application for direction finding zephyr/samples/bluetooth/direction_finding_connectionless_rx with minor modifications on nRF52833 DK. I...
Hello, I'm developing a BLE application under nRF51422 based on SDK12.2 using softdevice S130. Now, I'm porting the application from Keil to IAR 8.11. There is no compilation...
Hi,
SDK nRF5_SDK_17.0.2
Using :\examples\peripheral\saadc
I want support for multiple peripheral in same project, so i took the saadc example and on top of it add Uart...
Dear Devzone,
We are testing GPS of our products based on nRF9160.
When we test in one car, the GPS signal is lost when the device is put inside this car. This situation...
While testing DFU for OTA ,after entering bootloader mode on my nRF52840 DK, the device doesnt show up either in the device manager or using nRFconnect and Jflash lite . when...
I've 3 FTD nodes (nRF52840 SoC), the network between the nodes and the UDP message transfers are been done successfully.
I want to split and send the messages between...
Hello,
I am using your NRF9160 chip and need Nordic team help. I have refer to your FOTA sample, I am looking for a safer solution for updating code. On my board, I use...
Three software seems to perform OTA DFU: nrfutil command line, nRF connect from desktop, nRF connect from mobile
Do I need all three of them? Are they part of Nordik SDK...
Hi,
I am using an Adafruit nRF52840 Express with a sensor board attached to it. I'm noticing that my sensor IC is reading about 3-6dB higher noise in the 10-50Hz range ...
Hello,
I want to program and debug a custom PCB using the nRF52832 SoC and nRF52 DK. I plan to use this setup:
From what I understand, the GND detect will cause the...
Hi Nordic team,
We are busy testing the throughput of the nRF9160. We are having issues installing the NCS at this stage, and was thus provided with a HEX file of the Serial...
