void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
i am using nrf52840 USB dongle and the segger J_LINK EDU mini for debugging when i use bulid and run it works, and if i remove the donle and reinsert it then ts not working...
Hi,
I was using nRF command line tools 10.14.0 before. i try to update to 10.15.1 but fail with below log.
Do you have any comment for us to overcome this issue? ...
Using NRF Connect for Desktop V3.9.1 for Windows. We flash custom boards with J Link EDU 9.4 version. Since update to Programmer v2.0.1 it will not detect the J Link. Any...
Hi,
ncs1.8.0\zephyr\samples\bluetooth\periodic_adv\
ncs1.8.0\zephyr\samples\bluetooth\periodic_sync\
periodic_adv and periodic_sync
how to change to use Zephyr controller...
Hi,
I have a nRF5340 with USB DFU support which uses MCUBoot for upgrades. The current build (app_version_1) on the nRF has 0x4000 as the size of the settings_storage. The...
Hi,
Developing by NCS SDK, We found it will take 20 minutes by using mcumgr(on MacBook-pro) to BLE OTA 178KB image to nRF52840 Product Board's external SPI FLASH. it success...
The following is my set up:
platform: windows 11,
editor: visual studio code with nRF connect
SDK: nRF connect SDK v1.8.0
toolchain: nRF connect SDK v1.8.0 toolchain...
Hi,
Here is my hardware.
VBAT is 3.6-4.2V, UWB_EN is Pin28.By using nrf_gpio_cfg_output( UWB_EN ) to init this IO.
Is there any problem?Because when I using nrf_gpio_pin_clear...
Hi,
my product now is base on the nrf5340, I want to set the USB's serialnumber same as the ble mac address.
when I use the nrf52840, I can set it as follows simply. ...
Dear all,
My objective is to have an external MCU send data to an nrf52840 via UART and directly send this data via BLE to another nrf52840. I started from the ble_app_uart_c...
Hi,
I am developing an ANT TX application using the nRF52832 and SoftDevice S332. Things seems to be working well ... but I need one clarification As per the ANT example...
I am running the NRF52832 (BMD-300 module) and I'm trying to talk to battery over SMBus.
SMBus is compatible with devices up to 100 KHz.
I was wondering if there was a...
Hi,
nRF5340_PS_v1.0.pdf has multiple PIDR2 values to denote engineering versions of the chip. This seems to have been removed in subsequent product specifications, and now...
Hello, I tried to use pin_change_example in SDK to catch Interrupts (at first line) but I'm missing lots of them.
How can I catch all the interrupt events without delay...
