Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hello Nordic Team,
We have developed a custom PCB using nRF9151 and nPM1300 . Sometimes, the PMIC powers up and works normally; other times it doesn’t start at all. It occasionally...
Hi All
I have a question here.gatt Characteristic uuid has been Modified After the equipment has been in run for some time.
Current conditions of the equipment:
1.The...
Hi all,
I'm trying to use SPI Slave on a proprietary Hardware that use Ezurio BL54L15 (that contain a Nordic nRF54L15 chip). The environment is VSC + nRF Connect SDK 3.1...
Hello Nordic team,
I’m using the Mikroe nPM1300 PMIC Click Board (based on the Nordic nPM1300 PMIC ) with an ESP32 over I²C to charge a Li-ion battery.
Setup details:...
Hi,
May I know if the ncs add-on sdk-ant also supported nRF52833 because it is not mentioned in the list. Thanks.
Compatibility — ANT for nRF Connect SDK documentation...
Hi,
I need to use GRTC channel 0 in a nRF54L15 project. Channel 0 is special. It is the channel that the INTERVAL register controls. `zephyr/boards/nordic/nrf54l15dk/nrf54l_05_10_15_cpuapp_common...
Hello,
I’m designing a wearable device based on the nRF52832. To maintain time and date when the MCU and other sensors are completely disconnected from the 3.3 V supply...
Hi, I have an issue with nrf52DK, I cannod flash new version of my software. I have an error in VS Code:
* Executing task: nRF Connect: Flash: Aurora-nrf52/Aurora-nrf52...
Hello,
I am using Nordic nRF Connect SDK v3.1.1 and nRF5340DK board. My project is based on the project: GitHub - nordic-auko/nRF5-ble-timesync-demo: nRF52 clock synchronization...
Hi,
Has there any good course or training you recommend developing with LE Audio Development Kit either through Nordic official training or your preferred training program...
We observed a problem with our three different prototypes:
When there is only 5V-VBUS connected, the npm1300 does not ramp uo its voltages properly. The voltage rises up...
Hi there!
May I know how to have UART00 on P2 like what is shown below as I wanted to have higher speed.
Is it the same as other UART assignments on P0 and P1?
Thanks...
Hi Nordic team,
I'm currently testing the nRF9151 DK with a Conexa IoT SIM card in the United States (Philadelphia area). The board is flashed with the Asset Tracker v1...
Hello,
I a doing a ticket because I don't understand why my dht sensor doesn't fetch with my nrf54L15DK board.
Here is my overlay file :
/*
* Device Tree overlay...
