Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello,
I wanted to develop an Hearing Aid Application using nrf52840. I have downloaded nrf connect SDK but cannot find any samples for using HAP profile. Kindly provide...
Hello,
I intend to read the battery level of the nRF9160. I see that I have 2 alternatives to perform this function, using the AT%XVBAT command or reading the battery...
Hello!
I am working on a project that uses nrf52832 microcontroller with softdevice s132 6.1.1. for BLE capabilities. One of requirements is to implement directed advertising...
Hello,
I am building a product prototype based on nrf52810 with s112 7.0.1 with NRFDK16. So the problem is the memory allocation. I setup the FLASH and RAM as per specification...
Hello,
I'm using an NRF5340 with SDK V1.9.1.
I have a code that toggle one gpio pin on a custom board. It is working well when I use P0.22. However, when I change to P0...
Hi all I have a problem with the sim card on our custom board. Earlier I tested my code on nrf9160dk. But on the custom board, the sim card is not recognized. There is no...
We have an nRF5340 application that builds fine for our custom board. However, it is not very straightforward what steps need to be performed to enable FOTA updates. I have...
I am trying to use DTM to evaluate the output filter on our NRF52840 design. I am using the constant output mode and assume that the physical layer setting is not necessary...
Hey guys,
Recently I have been working with the nrf 52840 dongle and my goal is to use the dongle to communicate with a sensor and read values from it. So far I have been...
Hello,
I'm working on development of custom board based of nrf52811, we are using MAXM86161 and ICM-42605 on the custom board but couldn't find any drivers or library...
Hi, The attached picture below captures all the RSSI of our beacons in the field. These devices were set to transmit at maximum transmit power of +4dBm. This max value was...
Hi
I'm trying to get the application timer working on nrf52840 SDK version 17.02
I have followed the below link
devzone.nordicsemi.com/.../application-timer-tutorial...
I am able to print out to Uart but not able to receive from uart.
what do i get wrong?
/* main.c - Application main entry point */
/*
* Copyright (c) 2015-2016...
Hi everyone,
I would like to overwrite my SoftDevice wchich I don't use in my application. I found information about updates without Softdevice.
Its possible to update...
