Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hi, Is it possible to increase the size of the buffer for the UART IRQ RX function such that it receives more than 8 bytes at each interrupt? Currently I am trying to send...
Hello everyone,
I'm reaching out to touch base on the current support status on the latest software (MFW v1.3.1 and NCS v1.7.1) for CoAP over UDP (DTLS) for using as a main...
Hi,
I have a circuit with an I2C peripheral on a separate power switch. There is excessive power consumption (about 50µA extra) due to leakage after TWIM is disabled and...
Hi,
I am using a nRF9160-SICA-B1 and sometimes will see debug output that looks like this in Tera Term:
Glitch example:
Good example:
Basically it appears like...
Hi everybody,
I'd like to perform serial DFU on my nRF52832/nRF52840 based devices, using an external master MCU. Is there any reference C code for the master MCU? In this...
Hello. I am new to Zephyr. I cann't debug Hello_world sample. As i understand it always reboots and does not go to main.
I am trying to use VS Code and nRF Connect SDK ...
NRF Connect shows no device available.
usb interface MCU which embeds a j link is not detected by windows.
LED5 is blinking.
I have an external jlink to try to recover...
I had a project set up and working with my nrf52840 dev kit. It was using the 1.7.0 SDK and was based on the zephyr hello world sample. Today when I open VS Code, the project...
Hi,
On Segger Embedded Studio when you debug you also get the RTT console displayed at the same time. Is this possible on your VS code implementation? At the moment I can...
I'm trying to add 802.15.4 driver into my project (to implement an proprietary protocol).
The wireless_uart sample is very helpful and I got it up and running.
However...
I can find some other topics about this:
Like this one:
https://devzone.nordicsemi.com/f/nordic-q-a/43370/nrf_log_info-and-printf-does-not-work
or this article:
https...
Hello, I am new to firmware development and I am trying to stream heart rate data from an nrf32840 DK to an nrf32480 dongle and output that data. I am able to successfully...
I am trying to understand how to implement Serialization mode on nrf52.
Rather than having an observer on the application chip, I want the application chip to get alerted...
