Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
I am working on nRF5340 DK Here Blinky sample program in running successfully LED is blinking. while running HELLO WORLD sample program its shows no error but its not connecting...
Hello,
when switching from 1.8.0 to v1.9.1 release unfortunately modem delta update fails. I have also tried with v2.0.2 but without success. I am trying to update the...
I tried a few demos for the nRF5340-DK and most of them work fine. What's unclear to me is where the TX Power is configured or what the default TX Power is in the Zephyr based...
Can you provide an example of how a thread commissioned Matter device can request and retrieve data from the internet?
I understand how a Matter controller can get data...
Hi,
I'm trying to capture and communicate BLE devices on the Desktop/Laptop running Windows and MacOS.
My Application is to capture BLE packets, Connect to particular...
Hi,
I have an application project using nCS with following prj.conf file:
The issue is I am using nrf52833dk and the flash is only 512kb, my build file .bin size...
We have two products which are very much similar and have both an external RTC. So processor (nRF5340) and external RTC are identical. On one product, let's call it WP, everything...
Hi，nordic
I am using ses6.22a, the sdk is 1710 and mesh5.00. When I integrate the serial port case into the mesh sensor case, the serial port can work normally, but it must...
Hello guys, i'm attempting to record the radio_end event, and i tried to enable it with the following code:
However, the second line constantly crashes the chip.
In...
Hi:
I used the following command to install matter OTBR, but the following error occurred when executing this command;(sudo docker run -it --rm --privileged --name otbr...
hi,
I would like to purchase the following nRF-Desktop. It is a wireless BLE keyboard and mouse set.
https://www.nordicsemi.com/Products/Reference-designs/nRF-Desktop...
Hi,
I am using the nrf9160 and attempting to enable MCUBoot and secure boot. Is it correct that you still cannot use any form of TF-M with MCUBoot on the nrf53 or nrf91...
Hi,
I am currently using the NVS library with the nRF9160 and an external SPI-NOR flash device (MX25R6435F). I am getting concerned with the NVS library causing issues,...
Following Getting started with current measurements on the nRF9160 I applied the
to a Thingy:91 (disabled SERIAL, NCS-2.0.0). With that I get about 0,190 mA. That value...
