Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
Due to shortage of pins SPI CS is reconfigured as GPIO while SPI is not used. Soft device is not used.
Problem is the delay that is needed after nrfx_spis_uninit call...
Hi !
I use the NRF52832 and with Segger Embeded Studio to code.
The problem I have is that for some reason, my uart don't work after using an I2C write protocol and I...
Hi,
I tried to send a packet larger than 20 bytes by calling bt_nus_send on peripheral_uart but failed.
After checked on DevZone, I found some similar problem and did...
We are having connection problems with our nRF52832 based HID device only on Windows. I've attached packet captures taken with the nRF sniffer (nRF52 DK) and in Windows with...
Hi,
I looked at some of the questions on the forum and they didn't give me good advice. Currently all I can do is nrf52832 Security 1 Level 4 and nrf52833 Security 1 Level...
Hello
I try to write functions to modify the publish and the subscribe addresses. Unfortunately not all is working, attached you will find my code.
Problems:
1.pubish...
Hello
I'm using nrf52820 chip with Segger embedded studio and nRF5_SDK_17.1.0_ddde560 also soft device "s112_nrf52_7.2.0_softdevice" .
I want to add DFU through BLE support...
Hello,
nRF52840, SDK17.2, keil5, EC11 codec button
Output the same log in the positive and negative directions,
Turn one space: <info> app: cnt=-1 acc=1 accdbl...
Hello Everyone,
First of all, what a terrible experience this has been. I'm trying to use custom RSA private key in order to sign the firmware before we go into production...
Hello,
I am supposed to get to learn the nRF52840 DK, so I can start programming with it. I managed to build an executable for the blinky example using make in the Terminal...
Hi,
I'm having issues debugging a case where the device is reset / rebooted every 1-2 days on average for some reason without any error message as to why. If any error is...
We are porting a project from SDK 11 to nrf5 SDK 17.0.2. We have also used a couple of different versions of SDK 15 extensively on several different products.
Our code...
Hello, I'm trying to setup simple UART reception (interrupt driven) with Zephyr OS.
When a message over UART, only some characters are received, others just skipped.
Here...
Hey,
I am planning on using the Nordic SDK for some distance measurements between two nRF52840 boards.
For my documentation I would also want to understand how the technology...
Hi Folks,
I am bringing up a new printed circuit board with a Fanstel BT840 (nRF52840). When I install any firmware, even Blinky, it simply gets stuck in k_cpu_atomic_idle...
