void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi support team
One of our customer ask if it's possible to transfer a file system(LittleFS,refer: https://github.com/ARMmbed/littlefs ) to our Soc?? If not, are there some...
I am new to BLE and I am exploring Introduction to service. However I am stuck with Step 1 and Step 2. Is Step 1: static ble_os_t m_our_service; (to declare a service) and...
I have a device with no OS on it that talks serial through a UART to a nRF53840. I need to be able to update the nRF53840's firmware across the serial link, but since I don...
Hello, I am working on the BMD-300 Series Evaluation Kit with nrf52832 microcontroller and I tried accessing the serial number of my nrf52832, with these functions:
m_device_id1...
One doubt, if a node gets reset or disconnected , due to power failure in openthead cli mesh, dose it need to get configured again to join the mesh or will it connect to mesh...
First, by "Custom Protocol" I just mean that I need to directly access the radio to transmit or receive single packets occasionally. The literature appears to indicate that...
Hi, We flashed an ncs v1.3.0-rc1 build onto a 5340 DK network core, and ever since then the UART is not sending any data to our PC. We have connected RxD and TxD to pins P0...
I've seen a few discussions on C++ support. It's frustrating I can't contribute to the conversation - I'm not sure if that's because my account is too new, or if comments...
Good day, support!
I have a couple of questions regarding the mandatory services of the nRF52840 dongle.
1) How to add characteristics to the mandatory services 0x1800...
Hii,
I am trying to flash secure_bootloader into my nRF 52 SDK. I am facing some issue.
can you please explain how to create "micro_ecc_lib_nrf52.a" file (which software...
Hi,
I'm using NRF52840, and my application connects with BLE mobile application. After a minute, connection is lost.
I tried to find which functions called sd_ble_gap_disconnect...
Hi Nordic Team,
I am developing a device using Arduino Nano-33-ble board which is based on the nRF52840.
The code is developed on Arduino IDE and the basic function...
I am using SDK16.0(ble_app_uart) program to sending dates between the phone and board.And I noticed that send function (ble_nus_data_send）failed a few times when it didn't...
