The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
Hi, I am seeking assistance with a very weird issue encountered while programming an nRF5340 SoC using a custom debugging-PCB using a SEGGER J-Link EDU debugger.
The debugging...
Hello,
We use nrf54l15dk + MX25R8035F external flash to do the matter development on NCS2.9.0, and we meet some problems:
1. when the matter.ota is 1003KB, takes about...
Dear forum, I am testing out the radio on the nrf5340 using two evaluation board connected to a SES setup, but the receiving board only gets garbage and the checksum is never...
Hi all,
I have a custom board with an 9151, I want to use mqtt with aws, it's works I'm able to connect aws, but I have a question about
If I want to be able to connect...
Hello Nordic Team,
I am requesting clarification on the capabilities of my nRF9151DK to be used as a debug and flash probe (via the 'debug out' P20 headers), and compare...
I am developing a new architecture for my project. So, I am getting data from the peripheral, a custom nrf52832 card. Also, I create my custom service to send data and add...
I installed NRF connect I successfully built project when I flash I get success, but actually I can see project is not flashed what and how can I debug that ?
I am receiving the above error when trying to create a destination under "Device Management -> Message Routing Service -> Add Destination". There is no further indication...
I've recently encountered a problem where the Device Tree Visual Editor no longer displays any peripherals (ADC, UART, SPI), making them uneditable. I have had my own board...
Hi everyone,
We found that the LIS2MDL_INT interrupt from the compass on P1.06 affects communication between the app core and the network core.
About 3 seconds after...
I made some tests with PPK-II in source meter mode by connecting a load resistor in series with a Fluke 8846A ampere meter to the PPK output. A also hooked a GW Instek GDM...
Hi Nordic,
I am currently writing about the process of performing channel sounding sequentially on three connected devices. However, after the first channel sounding is...
Hello Everyone,
I am using NRF52840 dk evaluation board Arduino ethernet shield which has W5500 ethernet chip and for my development purpose using SDK 2.6.1 on visual...
hello to all.
i been strugling the last couple of days to make a simple PPP connection from a debian12 laptop to the internet passing trough the nrf9151. I followed the...
DECT NR+ HARQ communication and testing
Hello,
we using two nrf9151 development boards with latest modem firmware version DECT-NR+ (1.0.2) and nrf-connect v2.9.0 and...
