Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Dear Nordic-Team,
I designed a custom PCB using the nRF9151 as the host processor, the nRF7002 as a Wi-Fi companion, and the nPM1300 as the power management IC. The Wi-Fi...
Hello,
I encountered a strange behaviour on a nrf52832 : - I flash a a debug firmware (with debug optim in build config) : I can run debugger and add breakpoints - I stop...
I am developing an application that uses NCS2.8.0.
For FW updates, the nRF52833 USB ACM bootloader is enabled.
However, there are some problem.
My device has a battery...
Hi all hope you all are fine and doing well.
I am trying to use the Soft UART (uart-bitbang.c driver) on nRF52 DK for a low-speed UART connection. The initialization fails...
Hello, I am not sure if this is the most appropriate place to ask this question, but any comments are welcomed. I am developming a sensor platform that tries to use extended...
So hello everyone, I am a computer science student with zero IoT background. I am trying to a wearable device . I want to nrf52840DK with max30102 heart rate sensor and communicating...
Using nRF5 SDK 14.0.0 with Softdevice s132 v5.0.0 on nRF52832.
I've set up my nrf to be a GATT client (in central role), and I'm using bluez on my Linux desktop with a...
Hi,
we have a NRF52832 based project / product. We are using a DFU bootloader for application and SD update. The update is done from a master microcontroller using UART...
Hi Devzone,
Currently, we are attempting to use the Generic three-wire coexistence (refer link: https://docs.nordicsemi.com/bundle/ncs-2.9.2/page/nrf/app_dev/device_guides...
Hello,
I am working on a project which was previously developed by another person, and am struggling to setup the development environment. The project was built on nRF Connect...
Just got myself a ppk2, tried to set it up on linux, it wanted to update itself that didnt work on linux. On windows it did. Then tried to connect and it just keeps loading...
Hello,
I am currently working on a BLE Mesh–based control system and would appreciate guidance on a few architectural and scalability concerns.
System Overview The network...
According to the working principle of a crystal oscillator, the load capacitance is inversely proportional to the resonant frequency of the crystal, that is, the larger the...
Hi,
We are using the NORA-B126-00B module on our custom board, and the first time we flashed it with a simple LED blink example, it worked fine. However, after erasing the...
