Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
On Zephyr `2.7` I have following code to setup a SPIM on a custom board: Device tree:
main.c:
Now this no longer works on Zephyr `3.1`. I temporarily tried it with ...
Hello
I tried to install nRFConnect for Desktop, the latest version When I try to launch Toolchain Manager, I get an error "Unexpected end of JSON Input" error message....
Hello,
I works with Zephyr, VCS, SDK 2.0.0
I don't find how to get pin number from the DTS pinctrl .
In this folowing code, I want to replace magic number (uplighted...
Until toolchain update it was working well. But after toolchain update I cant even open toolchain manager . It just shows some exception like " Unexpected end of JSON input...
using NCS 1.9.1 - Zephyr - Segger Studio - sample code: bluetooth / peripheral_uart
I based my project on the sample, modified it slightly and it works well on a board with...
Hi,
I saw here: nrf52840 802.15.4: mlme_start_req: nonbeacon-enabled mode doesn't work
that the SDK-Version 14.2.0 was not compiled to work with non beacon enabled mode...
Hello,
After upgrading to the new version with the help of the migration guide, there is an issue that I could not trace back to any changes.
If I am correct its about...
Im compiling an app in nrf sdk 2.0.0 which works well on the nrf52811
as soon as I add
CONFIG_NRF_802154_RADIO_DRIVER =y
into prj.conf
without even initializing...
Hi Everyone,
I am working on NRF52833. I have developed code for our project. Now in this project the phone app will connect with the device using BLE for which I have implemented...
I have a Nordic Thingy:52 and Nordic Thingy:91, and I want to develop custom embedded software for them. Do I need a J-TAG or can I flash code using USB?
I've seen tutorials...
Hello,
I'm starting development with nordic arm processors. Therefore we purchased the BMD-360 EVK. This board features the NRF52811 processor and has the same pins as the...
We currently have a nRF52840 central device written with the Bluetooth Nordic SoftDevice API. From what I have read, the Zephyr RTOS is the best way going forward. I started...
Dear Nordic,
it's about USB implementation. We need to add interface string descriptor for ineterface name. Using USBD_STRING_DESCR_DEFINE(primary) I've added that to string...
Hello ,
I on the DK nRF52840, I wanted to manage the sleep mode and measure the current consumed by the microcontroller.
I started with example uart, I cut the PCB track...
According to the Nordic infocenter here
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcomp_matrix_nrf9160%2FCOMP%2Fnrf9160%2Fnrf9160_operator_certifications.html&cp...
