Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi,
I'm trying to follow the MCUBoot + SMP SVR example on this page: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/samples/subsys/mgmt/mcumgr/smp_svr...
My application uses NVS to store data and it works just fine - no errors reading or writing , and saved data persists between device power cycles.
My application also has...
Hi,
i have two nRF52833 program for make AOA. One is programe as Tx with "direction_finding_connectionless_tx" and one is program as receiver with "direction_finding_connectionless_rx...
Dear Support Team，
1. How to use Bluetooth Low Energy CGM service on NCS? Are there any examples for us to refer to? For example, nRF5_SDK_17.1.0_ddde560\examples\ble_peripheral...
I turn on the device, the led turns green. And I use usb to connect it with computer then I open the nrf connect for desktop, the bluetooth low energy tool,
10:51:05.822...
Hi,
Our custom board using the nRF52840 with SDK 15.0.0 experiences a higher current draw if it starts up without the USBD module enabled at some time. The first screenshot...
Hi, I work with SES on an nrf52840 on a custom board. Here is my issue :
My board can be wakeup from SYSTEM OFF with 2 interrupts on 2 differents GPIOs : 1 is connected...
hello Nordic
sorry to nag but i am waiting for an answer on the thread below for more then a week now, hope you can attend to it or at list inform that you are working...
Hello Devzone,
Working on my Ubuntu 20.04 LTS host, I recently lost ability to flash my nRF9160dk board. The embedded J-Link is detected by its serial number, but an attempt...
Hi, we are working on an application with 300 nodes. each node do 10sec advertsiment and afterwards 10sec scanning pls check the picture below
1) Beacon2 for example advertisies...
Hi,
I have added an external reset switch on my custom board. Maybe a stupid question, but do I need a pull-up resistor? Because in de schematics of the nrf52840 dk I didn...
Hi,
i want to send and receive data via uart1 (connect to a raspberry and send/receive text).
Is there a simple example that shows how to accomplish this?
Im using SDK...
I'm trying to implement a really simple script to sample voltage values from 5 different analog pins on my NRF52832 DK (using Segger at the moment). I found the SAADC example...
While nrfconnect-3.11.0-x86_64.appimage works well, the update to 3.11.1 ends up without Apps.
Ubuntu 18.04
NCS 1.9.1
I found a past case and removed the config and...
