Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
I am currently working with the Nordic nRF5340DK board using the official Matter light bulb example from the nRF Connect SDK version 3.1.0. I am also using the nordicconnectedhomeip...
We are designing a board around nRF54H20, and nPM1300, with some peripheral on VSYS, some on V3.0 BUCK2 and other are on V1.8 BUCK1. We also have detachable battery in place...
Hello,
Is the value readable by AT+CGSN the correct IMEI for the nRF9151?
Is there a way to read this value using JLink (nrfjprog)?
IC: nRF9151
SDK: NCS v2.9.2
Base...
Hello,
I received an email regarding the new course for nRF54 series parts and when I click on the link I am blocked by a Cloudfare generated web page. The Cloudfare ray...
Hi, We currently have a custom board with a nRF54L15 (final production silicon) paired up with a nRF21540 RF front-end module (FEM). This board is running Zephyr with v2.9...
Hello! I am using the nRF7002 in promiscuous mode to capture Wi-Fi traffic. Everything went smooth in AP mode where we use another nRF7002DK as a transmitter and our computer...
Hello,
We are entering preproduction build for a custom design using the nRF54L15. We need to know the solder ball dimensions and the recommended solder-mask dimensions...
Problem:
Reset reason logic works correctly when programming via SWD
After DFU programming, reset reasons are detected incorrectly
Even after unplugging/reconnecting...
Hello all, I've just bought nRF9151 DK and went with Quick Start. I loaded nRF Cloud multi-service sample. Sample runs and connect to network. Sometimes it sends data (location...
I am following the Cellular IoT Fundamentals course and trying to get my nRF9151-DK set up as a device in the nRF cloud. ( https://academy.nordicsemi.com/courses/cellular...
Hi
I have two nRF54L15 DK boards (PCA10156).
Both are behaving the same way right now.
.......................................
ONE: Using nRFConnect in VSCode...
Hi,
I am currently developing a heart rate strap using SDK 17.1.0 and the S312 SoftDevice with the nRF52805. I have noticed an issue: when I connect the heart rate strap...
Hi
I'm using the periodic_adv_conn example from SDK 3.0.0. In the request_cb function, the bt_le_per_adv_set_subevent_data function is used to load data for future subevents...
Hi,
I want to use the die temperature sensor in the nRF54L chipset and am wondering why the definition have changed slightly compared to previous chipsets. In the SoC device...
How precise do the trace antenna dimensions have to be? Given that the datasheet for the nRF54L15 only has a reference layout up to and including the matching network, but...
