Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hello,
I am trying to perform full modem FOTA update on my nRF9160 DK board using sample code without using buttons press functionality as we want to integrate the same...
Hi,
We are developing a product (to be produced in small quantities only) that included USB data transfer based on your USB CDC ACM module. We do not have our own USB vendor...
Can an iBasis sim card be activated without being in a device (nRF9160dk or Thingy:91).
I have two sim cards and neither will activate.
Most of the time after entering...
aoa rx hardware: nrf52833DK
aoa tx hardware: my test nrf52833 board
my test nrf52833 board download "direction_finding_connectionless_tx", use " overlay-aoa.conf"
nrf52833DK...
We are currently in the process of looking into the Bluetooth certification as part of a Homekit accessory, and the documentation raised some questions:
the QDID for the...
Hi,
I'm new to ble.
In order to better understand what is going on, on a packet leveI got a packet sniffer.
I found a device that uses a nordic chip, and am trying...
Hi, I am trying to develop an nCS application with serial flash interface, I am using an nRF52833dk & I observed that under the nCS path "v1.8.0\zephyr\drivers\flash" There...
Please guide what changes are to be done for the Light bulb example to be run in 52840 Dongle?
I am using VS Code and built the Build Configuration using the Dongle configuration...
Hello.
I am yoo at korea.
We will connect OLED with QSPI and Driver IC supports SLOWREAD.
- 8bit (Opcode: 0x03) + 24bit (Addr) + 8bit (Read value: Mandatory) + 8bit...
Hello.
I have question for QSPI OPCODE.
According to "nRF52840_PS_V1.5", WREN optional at "the custom Instruction".
- using function: nrf_drv_qspi_cinstr_xfer
...
Hi, I'm trying to use light_lightness example , and button_event_handler didn't work.
Error message is
"multiple definition of "GPIOTE_IRQHandler" "
because I added...
Hi, I'm using nRF52 DK. I'm following tutorial links 1 , 2 and 3 to learn how to add BLE OTA DFU to the example project ble_app_uart.
Step 1
Following the above links...
Dear ,
I am currently testing the UART peripheral on nRF52832 and nRF52840 using nRF Connect SDK.
Basically, I have a sensor that continues sending out data via uart and...
I'm trying to build the pc-ble-driver ( https://github.com/NordicSemiconductor/pc-ble-driver ) to be able to use the nRF52840 as a receiver for a thermometer. See https:/...
