Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
We developed firmware based on the sample provided at the following link to pass Japan's technical standards compliance test https ://docs .nordicsemi .com /bundle /sdk_nrf5_v17...
I tried to use nRF54L15DK for program development, but so far I have run into some issues:
I wanted to use the coprocessor from nRF54L15DK to do some data processing, and...
Previously, nRF Connect SDK was working without issue. However, now when I try to create a new build configuration, it hangs at the following step:
It's unclear why this...
The instructions are: On the command line, open the directory ncs . The following steps have one do a west init directly in the directory ncs. But they should say to create...
i used sdk version 15.2 everything work fine but in ios 15 its not show services when android work fine and ios 14.8.1 also work fine and show services please help
There are multiple errors:
Failed to clone the repositories: Error: Cloning into '~/ncs/v2.6.1/.west/manifest-tmp'... /~/ncs/toolchains/2be090971e/usr/local/libexec...
When initially starting Sidewalk on BLE it seems that the current consumption is high if you start with only LINK1 enabled. It seems that perhaps this is due to the SX1262...
I am using Wireshark 4.4.0 and Nordic nRF Sniffer for Bluetooth LE 4.1.1 (nRF52840-Dongle PCA10059). In Wireshark I see a device, a peripheral, sending advertising packets...
hey, I am using nrf52840 in that i am making it compatible with DFU by using sdk2.8, but getting this error
C:/ncs/v2.8.0/nrf/include/flash_map_pm.h:47:22: error: 'PM_mcuboot_secondary_ID...
hello!
I am currently using the nRF7002DK to implement the examples from nRF dev academi. I am practicing based on lesson 5-exercise 2.
lesson 5 exercise 2
In the example...
Hello, I want to make my project DFU OTA compatible, so when I tested on development it works fine once I created my pcb using nrf52840 module in it. So it is taking huge...
Hello,
I have a question regarding a recent issue.
I'm currently developing with the nRF52840 IC or EVM, and I'm facing a problem. Whenever I write firmware to the flash...
Hi Team,
I recently purchased 2 Audio DK's and I set one up as a gateway and the second as a left headset. I was able to pair the two, stream audio from my PC through the...
Hi,
We are currently developing a BLE device (HW and SW) using the NRF52811.
As we want to be able to update the device via FOTA we need to have the Bootloader to have...
