I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well. ...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi all,
I am trying to use MCUBoot on the nRF52840, and am having troubles with this: Whenever my device boots, it always immediately goes to bootload mode and I can't get...
hi all,
ST7735 driver for TFT Display which is tested using example/peripherals/GFX library, we want to test touch screen for this display ,the touch screen driver used...
I am currently working on a project using the nRF52840-DK and the Power Profiler Kit II. I have created an application based on the "NFC System Off" sample. However, I am...
Hi could you provide any insight on the following issue:
Source code in main.c
#include <zephyr/kernel.h>
#include <zephyr/device.h>
#include <zephyr/drivers/sensor...
Hello,
I have developed a Zephyr BLE project with the MAX30102 sensor. I tested the code successfully with the nRF52833 DK, and it works fine. Now, I am trying to flash...
Hi,
Our system includes an nRF52840 (ncs2.4.0, zephyr) as a Host and a NAND (Macronix MX35LF2G24AD) as a flash; communicated with each other via SPI.
At Host, we can do...
Hi,
My customer tried using the keyboard we made based on nRF Desktop with NCS version 2.1.0 with an iPad and noticed that most of the keys work, but space bar does not...
64 bit unique device identifier. DEVICEID[0] contains the least significant bits of the device identifier. DEVICEID[1] contains the most significant bits of the device identifier...
Hi there,
I have successfully enabled CDC ACM Serial Recovery mode on the nRF5340, which allows me to update the application and network core with two separate .bin files...
I'm trying to create a board configuration for MicroPython under the Zephyr port for the nRF9161 and add functionality to use the DECT modem. I'm following the example code...
Hi
I have used the nsc-sbom utillity to generate an SBOM for my project.
However, instead of the HTML output format I need to generate it in a FDA recognized format...
Hello,
I'm currently working with the nRF9160 to utilize Cellular Monitor to connect the board to a cell tower. It is capable of connecting and filling out the chart in...
I have bought a brand new nRF52840 Dongle that I want to flash. I have installed nRF Connect for Desktop from https://www.nordicsemi.com/Products/Development-tools/nRF-Connect...
We want to use the nRF7002 in our product and supply it with energy using a LiMnO2 cell in CR2 format. The LiMnO2 cell has a nominal voltage of 3.0V and a maximum voltage...
GPIOTE has higher current consumption than port events. We are trying yo use PORT events to detect GPIO inputs with buttons. But we are not successful, is there any example...