I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hello,
I have a question about the Kconfig extension for VSCode.
When I use the nrf52840 DK, the Board Selection correctly check the nrf52840dk_nrf52840 and all the configs...
I've been continuing to work on why my power level seemed low after getting the Skyworks FEM in my Fanstel BT840x module going, per this thread:
So far, I've been setting...
I want to increase the rate of data from UARTE to RF FIFO.Can data be transferred from the cache to the RF FIFO using DMA?
nrf52832 nRF5_SDK_17.1.0_ddde560 S132
Hello, I am trying to understand the adc example using the PCA10056.
HI can see the following code that initializes 3 `zephyr_user` channels
In the DT file,...
Hi,
I recently went through the manual installation instructions for the nRF Connect SDK posted here ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_installing...
Dear,
I would like to remove the DCDC converter in between the li-ion cell which is supplying the system and the system.
The idea is to use our micro battery as the...
Hi All, I have the same issue than in this thread :
To explain fastly, I am using the pc_ble_driver_py v0.15.0, with a nrf52840 Dongle to try catching voice sent by a device...
Getting this issue while building the code I have tried these given options but did not worked out . Please help me with this. I have included all the required driver files...
Our Setup
STM32 Chip (master) connected to nRF52840 (slave) via UART
STM32 is supposed to update the application on n RF52840
nRF52840 runs the secure UART bootloader...
Hi There,
I am currently developing the firmware for a peripheral device using the NRF52840 and NCS V2.0.0.
At the moment everything is working as expected except for...
Hello,
I'm evaluating using the opus library included as a of the "nRFready Smart Remote 3 nRF52" as a part of our zephyr based application. We only need to decode stored...
Hi,
I've installed "nRF Connect for Desktop v3.12.0" on Win 10 (Version 21H2, Build 19044.2006) and then installed the Programmer v3.0.4 out of nRF Connect. Installation...
Hi Nordic Guys,
hope you can help following issue (I think the issue is still mentioned in Ticket https://devzone.nordicsemi.com/f/nordic-q-a/87410/corrupt-matter-zcl...
