Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
How Can I store information about button port ? I have two buttons P1.02 and P0.02. I have
And I have one function to init button
the most interesting is callback...
Hello to all,
Below are the setup details I'm using:
nRF52840 DevKit
SDK: nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
Segger Embedded Studio 4.16
I am working...
I'm trying to run LTE/BLE Gateway sample on nRF9160DK , i followed all the instruction in the sample instructions.
The Jlink RTT for nRF52840 and LTE-Link Monitor logs are...
Hi nice people, I am working on developing using visual studio and Make environment. I am trying to function UART tx/rx interrupt works but no luck. The TX and RX works perfect...
Hello, I've been trying to launch zephyr SPI example, but I'm having issues with SPI sending anything. The code itself does not throw any errors, and it seems like my board...
hello sir ,
i am using thigy91 board and uploaded the asset tracker application code from ncs sample code . ii am getting humidity data on my azure cloud .but there was...
Hello everyone!
We are using nRF51822 SoC together with s130 Softdevice. nRF5 SDK v12.3.0 is used for firmware development together with the Segger Embedded Studio.
Among...
Hardware: nrf9160DK Modem FW: v1.3.1 We have been evaluating and configuring our proprietary application for NB-IoT, which is initially designed for LTE-M (CAT-M1). The Application...
Hello,
I'm using a central device that lists all nearby peripheral devices by their MAC addresses like so:
but I also want to list the names of the devices as they...
Hi Nordic,
We are preparing to validate a product that contains the UBlox BMD-340 with the Nordic Softdevice. We would like to use the Nordic Semiconductor “nRF Connect...
Hello!
I have used most of the GPIO pins on the nRF52DK, and most of them work. But I cannot get pin 21 to behave. I want to use it as an input. I have configured it as...
In nRF_SDK_For_Thread_and_Zigbee, on the nordic BSP package following three-button functionalities are available:
#define BSP_BUTTON_ACTION_PUSH (APP_BUTTON_PUSH) /**< Represents...
Hi,
I have 2 boards, one with monogoto esim and one with ibasis esim when I try with monogoto everything is working fine
when I try with ibasis esim i can't get registered...
Hi all,
I have a problem when I try to debug nRF52832 target. The nRF52832 chip is advertising properly but as soon as I enter in debug mode, advertising stops. There is...
