Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I am using Zephyr to create a program that integrates BLE Mesh and NUS. My goal is to use a sensor_client to read data from a sensor_server, and then send the data, via peripheral_uart...
Need some help with:
nrf5340 - custom board
NO external Flash
DFU over BLE with simultaneous update of both images allowed ( using this devzone concept with static...
I using a BMI323 sensor with address 0x68 on the I2C bus and a custom-made nRF52832 dev kit. when I tried to send some commands to the sensor via I2C, it didn't work.
here...
Hello, I'm writing an application for nRF91 series and I have the functionality mostly working but the "sleep" current is high, about 4-7mA. I assume that this means that...
Hi,
I am currently working with the nRF5340 Audio DKs and have successfully implemented the gateway and handset functionalities.
Now, I want to extend the system by enabling...
With the mcuboot enabled, I'm not being able to disable the boot banners even by doing the below settings in prj.conf file.
CONFIG_NCS_BOOT_BANNER = n
CONFIG_BOOT_BANNER...
Hi!
In our project, we need to send cloud-to-device commands. By "command" I mean a request to do some short action, not a request to change device's configuration/state...
Dear Nordic Team,
Today, as of January 30, 2025, our devices started giving the same error and we are no longer able to receive any location data from nRF Cloud and even...
Hello,
I'm currently working on a project that uses the PMIC nPM1300. We need to monitor the battery's SOC, capacity, etc. As far as I understand, I need to use the fuel...
We have a number of graphical assets that are taking up a significant amount of flash space on the nrf52840. I would like to use memory external flash over QSPI to store the...
Using the LVGL sample... The sample LVGL code works on nrf52840dk but not the RAYTAC MDBT50Q . I hope I'm just missing something obvious?
Flash blinking to nrf52840dk...
Hello !
I am using using the chip BT840F of Fanstel (based on the nrf52840) powered by an external 3.0 v battery for my beacon BLE application.
Regarding power consumption...
On Friady we were finishing off our final testing for our nRF5340 based product (SDK 2.1) when we discovered we couldnt do firmware updates from Samsung Galaxy Tab A8 tablets...
I like to use the DTM mode in a test mode of our device based on nRF5340. Using SDK 2.7.0 with Zephyr. Started with using the DTM example but it does not build. Beyond other...
I've purchased a couple of nRF5340 Audio DKs for testing Auracast broadcast source/sink. Installed VS Code and have the sample apps built & flashed.
SOURCE: Sample app bap_broadast...
