Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
Hello,
I am working with nrf5281 and its bluetooth connection, the connection is established well and the chip and the nrf connect application stay connected, however the...
Hi,
I recently installed nRF Connect SDK v1.6.0 through the Toolchain Manager of nRF Connect. Previously v1.5.0 was installed, and was what I have been developing using...
I am trying to implement the buttonless dfu example, I successfully managed to upload the template example examples\ble_peripheral\ble_app_buttonless_dfu and can see it advertising...
Hi all,
I'm working on a limited power budget system. MSP430 is the master that is supplying power to nrf51882 (slave). Every 2s MSP430 derives a pin high to drive the nrf51...
nrf9160 modem Firmware version 1.3.0 release listed nidd or non-ip support. in the firmware.
We are eager to use this feature to send/receive data over RF control plane...
"CTE can be used in both connectionless and connection-oriented scenarios. For connectionless use, the periodic advertising feature is required (since deterministic timing...
Hello all,
I'm using NRF52840 with last sdk (V1.6.0) of nrf connect but I can't put the device into sleep mode (where the current consumption is at about 3/4 U) the device...
Hi,
I need a 1Hz clock with its interrupt function.
Where do I find an example to set the timer RTC0 or RTC1 to 1Hz and how to set the timer callback function?
Thanks...
Hi,
I am using nrfx_twim driver, and I want to read value from sensor's register. When I want to do that sequence looks something like this:
(SENSOR_I2c_ADDR+Read_bit...
Hello Sirs
I have two questions about the nrf5340-dk evaluation board.
The first one is how can I get the scan data of an advertising device?
And the second is that...
Hi,
My dev environment is as follows:
nrf52840 + s140 +SD7.0.1 + SDK17.0.0.9 + SES + nrfutil v6.1.0
I started my development for DFU and utilized secure buttonless DFU...
Hi there,
Currently, I am getting an error with a low power node when the remote cannot configure through another regular node in a mesh network. What causes me to get this...
Hello Nordic support,
I would like to use the APIs in IEEE 802.15.4, especially mlme_scan_req in nRF5 SDK for Thread & Zigbee for a ZigBee application in order to scan for...
I want to use the Nordic UART/Serial Port Emulation over BLE to communicate to a windows or linux host computer.
I see Andriod and IOS haveapps available to support Nordic...
Hello,
I have upgraded my project from nRF_Connect 1.5.1 to nRF_Connect 1.6.0.
It runs on nRF9160 and I use RTT viewer v7.50a.
The problem that I see is that the logs...
