Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
im trying to do notification for characteristic of a service whenever i trying to notify from nrf mobile app the debug session in ses is stopping its play in few seconds
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
Assume I have one FDS record. With this...
Hello,
If I understand well the characteristics of the Thingy.91 si that you supplie a firmware we can download and modify as we want because it is open source, is that...
We're trying to diagnose an issue that's occurred to at least two of our customers. For some reason, we've found two different iPhones that are seeing our reader (nRF52840...
Hello,
Float printk (%f and %0.2f) is not working. I use newlib and activated floats for print and scan support without success.
Configuration:
Version from 31 january...
Hello!
I use nRF52-DK wuth android device. DK connects to android device and works with it well. But I want a paired DK make unpaired from android device by performing unpair...
Hi,
I have requirement of BLE node to node communication in mesh network.
All the nodes should have single firmware which will be capable of publishing and subscribing...
Hi All,
We are trying to interface nRF52840 based custom board, manufactured using Config 6 schematic as the reference, with R-Pi to work as NCP. Please refer to the attached...
EDIT: It seems that the app hangs in nrf_saadc_event_check() after initializing channel0. I'll further investigate!
Current I'm at the point at which I found out that
...
Hi,
I'd like to start developing automated tests for my custom NRF52840 board.
Currently I use the CLI library (with RTT backend) for communicating with the board.
Any...
Hello once again Nordic Pro's,
My latest issue, I believe to be related to stack/heap settings, but dont have enough information to track/correct.
I have a couple int...
Hi,
I am working on nrf52840. I am using SDK 16.0 version.
I have issue while compling example code of blinky_freertos( nRF5SDK160098a08e2\examples\peripheral\blinky_freertos...
I am working with an nRF52810 and nRF52832 (SDK15.3.0), with an Android app based on Android BLE Library 2.1.1. In both cases sdk_config.h has
#define NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
The link provided on this page, while selecting "macOS" from the left, and clicking the first link ( v10.6 ) provides the following link:
https://www.nordicsemi.com/-/media...
Hello I try to open a nRF project on a MacOs with the correct installation of all the toolchain and zephir. However during the configure I have always problems one solved...
