Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
Hi Support Team
Is the oversampling mode the highest accuracy mode for the SAADC of nRF54L15? The datasheet mentioned a formula to calculate the improved SNR. What is the...
Hi Team, I tried adding battery reporting to the Matter bulb demo based on the nRF54L15DK. The device was successfully added to the Apple Home app, but I’ve noticed that it...
Hi,
I'm trying to enable support for MT25QL01GBBB memory on nrF5340DK. Existing flash has been soldered-off, the one from Micron has been soldered-in with two pull-up resistors...
Hi, I was curious if the orientation of the devices matter for channel sounding using NRF54l15. I have noticed that channel sounding works best when the initiator and reflector...
Hi,
I am trying to get an nRF54L15DK working with an nRF7002EK using SPI (not QSPI) and I cannot get this working using the wifi-scan sample.
I am using nRF Connect SDK...
I'm attempting to migration from using MCUBOOT as a child image to sysbuild using SDK 2.8.0.
Everything boots fine when building using a child image, but when switching...
Hello, I tried the example from the exercise. I dint change anything which means I didnt activate timeslicing yet and I already get the output: Hello, I am thread0 Hello,...
I flash my firmware onto the nRF52840-DK and want to profile the power consumption of the nRF52840 chip, but not the other DK specific stuff like JLink. How do I exactly wire...
Using connect SDK 3.0.2 and a NRF-DK52840 my goal is fairly simple: My app should be updatable via BLE using a static partition table. I followed this tutorial: nRF Connect...
Hi,
I am trying to set up a half duplex UART in async mode over pin 1.9 on NRF54DK board for my project:
Overlay file:
& uart20 {
compatible = "nordic,nrf-uarte...
Hello Nordic
We're developing an application where the second firmware partition is saved in external storage, which we would like to be accessible by both MCUboot and the...
I will calculate the capacitance of the external capacitors for the 32 MHz oscillator circuit, but the values of the Cpin for XC1 and XC2 are not specified in the the datasheet...
When I follow the use_gpio_pin_directly manual I get a compilation error:
```
/home/gal/dev/ism330bx_driver_contribution/zephyr/include/zephyr/devicetree.h:196:36: error...
Hello,
I'm tinkering (motion detection mostly) with a Thingy:91 unit (I don't have a DK board), and in general it works fine reporting sensory data to AWS IoT Core.
Last...
