Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Does anybody know the maximum throughput and minimum BER/PER of nRF51822 at a 1~2 meter distance?
Also, when the datasheet says it supports up to 2 Mb/s, is it still with...
Hi,
I have a MBN5283DK from murata, and I am trying to program the simple blinky example on it. The thing is, using nRFgo studio, I programmed the hex file onto the board...
Hello, I am working on detecting extended advertisements on the nRF52840, with the extended advertisements coming from a Google Pixel 2 phone.
I am basing my program on...
I am receiving data from a phone, i want to send back a word .
So , this is probably wrong but , to send :
void sendBluetoothData( uint8_t data[], uint16_t length)
...
I am a novice who now deals with nrf52 dk.
I installed command line tools according to the guide in the link above. I have installed several jlink programs, of which I do...
Hi,
I enter problem when I tried to delete bonded data from my example code using pm_peers_delete()
SW: nRF5_SDK_15.2.0_9412b96
HW: PCA10056
example: ble_app_hrs_freertos...
nRF9160 DK: I followed the userguide , devzone.nordicsemi.com/.../getting-started-with-nrf9160-dk
I done with 2 examples: AT Client and Asset Tracker examples. I passed...
Hi,
I am developing against a custom board built around the NRF52840. I am trying to store and retrieve values from flash using the fds module. I am not seeing any errors...
Hi, I am going to use the nRF91 DK to program an external PCB with the nRF9160 on it. The DK documentation says that only 1.8V or 3.0V is supported for external debug/programming...
I am running on a Windows 10 PC.
I've downloaded and installed all the tools for the nRF9160 DK using nRF Connect.
After installing the Segger Embedded Studio, I followed...
Parts of this discussion started on this thread: i-am-trying-to-do-dmx512-protocol
I am using SDK 15.2.0 on an nRF52810. My test board is based off of a Laird BL651 which...
I am trying to setup SEGGER Embedded Studio to program the nRF52840 dongle hardware. I followed the Getting Started Assistant program to set up the development software for...
The SDK version I am using is V15.0.0.
I use the function interface nrf_gzll_set_pa_lna_cfg 。 The following is my configuration information：
static nrf_gzll_pa_lna_cfg_t...
Hi dear community,
I am currently using nRF52 DK which has 52832 on it. I am using it for my bachelor thesis project and want to create simple sensor network. I am using...
