I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
We are seeing LTE-M communication dropouts on the nRF9160 with firmware 1.3.6 This has occurred several times with multiple devices. The devices are registered on the same...
NCS: 3.4.0 Chip: nRF54L15 Hello, in the past months, there has been quite a change regarding Security and Vulnerability Monitoring on the Nordic Semiconductors side. I got...
Hi,
We had connectivity issues on our end for the Message Routing Service webhook since May 13, 2026. It has been restored and tested with the nRF Cloud verification test...
Hello:
Hello Nordic Support,
We are developing a battery-powered product based on the nPM2100 and nRF54L15 , powered by either a CR2032 or CR2450 primary coin-cell battery...
Dear Nordic team,
we are evaluating the nRF9151 for a data acquisition application/device. Our first goal was to get the official HTTPS client sample to run on the nRF9151DK...
Hi ... have code that outputs I2S in master mode. The slave, a NAU8822 device requires Master Clock Source between 8 and 33MHz.
The 54L MCLK pin is duplicating the BCLK...
To use the nRF54L15 SPI00 and SDHC, I have to edit the SDHC file and add board-specific configurations to start at a 1 MHz clock, since the SDHC file defaults to a lower frequency...
Hello,
I was going through "Bluetooth Low Energy Fundamentals" https://academy.nordicsemi.com/courses/bluetooth-low-energy-fundamentals/ .
I feel few need to be corrected...
Does Nordic make available 3d models (.stp files) for the nrf7002, nrf5340, and/or npm1300 chip scale parts?
The only information I can find on this is in a forum post...
Problem After successfully establishing a nRF7002EK WiFi connection to the local network, AWS IOT connection fails with “mqtt_helper: mqtt_connect, error: -2” and reboots...
Problem When attempting to flash a nRF board that uses pyocd as the runner (defined in devices’s baord.cmake) for flashing, the following error occurs.
It doesn’t matter...
Hi Nordic team,
I am currently researching Bluetooth Channel Sounding, where I have setup two nrf54LM20-DK as intiaitor and reflector respectively.
I am using NCS 3.3...
I'm developing a custom BLE sensor on an nRF52832 (E73-2G4M04S1B module, SoftDevice S132 7.2.0) with a companion Android app. On Xiaomi/HyperOS devices (confirmed on this...
Just purchased the PPK 2 Did the quickstart up and got this a message saying it's not yet supported. I am running Ubuntu Linux :
Distributor ID: Ubuntu Description: Ubuntu...
