We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Dear Team,
I am trying to use smp_bt_register and smp_bt_unregister calls in order to add/remove BLE SMP characteristic in real-time.
However, I keep getting 'undefined...
Hello,
I know that this issue comes up from time to time. I'm raising it again, because to my opinion there have to be a solution for this. Perhaps there is, that's the...
I am currently working with the Nordic nRF5340DK board using the official Matter light bulb example from the nRF Connect SDK version 3.1.0. I am also using the nordicconnectedhomeip...
We are designing a board around nRF54H20, and nPM1300, with some peripheral on VSYS, some on V3.0 BUCK2 and other are on V1.8 BUCK1. We also have detachable battery in place...
Hello,
Is the value readable by AT+CGSN the correct IMEI for the nRF9151?
Is there a way to read this value using JLink (nrfjprog)?
IC: nRF9151
SDK: NCS v2.9.2
Base...
Hello,
I received an email regarding the new course for nRF54 series parts and when I click on the link I am blocked by a Cloudfare generated web page. The Cloudfare ray...
Hi, We currently have a custom board with a nRF54L15 (final production silicon) paired up with a nRF21540 RF front-end module (FEM). This board is running Zephyr with v2.9...
Hello! I am using the nRF7002 in promiscuous mode to capture Wi-Fi traffic. Everything went smooth in AP mode where we use another nRF7002DK as a transmitter and our computer...
Hello,
We are entering preproduction build for a custom design using the nRF54L15. We need to know the solder ball dimensions and the recommended solder-mask dimensions...
Problem:
Reset reason logic works correctly when programming via SWD
After DFU programming, reset reasons are detected incorrectly
Even after unplugging/reconnecting...
Hello all, I've just bought nRF9151 DK and went with Quick Start. I loaded nRF Cloud multi-service sample. Sample runs and connect to network. Sometimes it sends data (location...
I am following the Cellular IoT Fundamentals course and trying to get my nRF9151-DK set up as a device in the nRF cloud. ( https://academy.nordicsemi.com/courses/cellular...
Hi
I have two nRF54L15 DK boards (PCA10156).
Both are behaving the same way right now.
.......................................
ONE: Using nRFConnect in VSCode...
Hi,
I am currently developing a heart rate strap using SDK 17.1.0 and the S312 SoftDevice with the nRF52805. I have noticed an issue: when I connect the heart rate strap...
Hi
I'm using the periodic_adv_conn example from SDK 3.0.0. In the request_cb function, the bt_le_per_adv_set_subevent_data function is used to load data for future subevents...
