Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello, I'm having the same issue as in this thread but the proposed solutions doesn't work for me. This is the output from the terminal:
*** Booting Zephyr OS build v2.7...
Hello, I tried to upload a simple blink sketch from pca10040 which works for nrf52832 to an nrf52810. But it didn't work. Then I tried pca10040e. It worked for nrf52810. ...
I accidentally clicked verified answer while trying to edit the page.
https://devzone.nordicsemi.com/f/nordic-q-a/87116/apply-the-heartbeat-publication-and-subscription...
I want to be able to send the "AT%" type of Nordic proprietary commands to the modem (and read the response back) via firmware on the nRF9160. I know about the
nrf_modem_at_cmd...
Currently I have been able to advertise and connect through debug app using nRF52 DK. My target is:
1. After the link is lost the bluetooth gets disconnected and at this...
I have been using Segger Embedded Studio to develop in and recently switched to use VS Code with NCS. It was always very useful to use Segger's watch window with the real...
Hi All,
I want to add pairing and binding functions to the blinky project.
But nothing happens when I connect.
Please help me,thank you.
Here is my project =>
...
Hi,
I just tested an SPI loopback example on nrf52833 board from the bellow code
https://elixir.bootlin.com/zephyr/latest/source/tests/drivers/spi/spi_loopback/src/spi...
I have an nRF52840 dongle I got from someone else that doesn't have the nrf bootloader on it. When I plug it into a USB port, the red light flashes quickly while a green light...
hello,
i have downloaded ( BSEC ) library from https://www.bosch-sensortec.com/software-tools/software/bsec/ for read sensor data . now want to test the code by build and...
I am using the latest code(v1.9.0-rc2). The board is nrf52833_nrf52833. The board overlay file set antenna number to 13. (The original value is 12).
It seems that...
Hi,
I'm trying the USB Audio in ncs .
dts is like below:
And prj.conf:
CONFIG_USB_DEVICE_AUDIO=y and other USB relevant defines.
It works,and the usb audio data...
Hi,
i upgraded the nRF Connect SDK from 1.8.0 to 1.9.1. During the install i have chosen a different install path - to have the same current path in different locations...
We were developing an nRF52840 device and were working on MCUBOOT DFU firmware updates, and accidentally did an update rather than an upgrade, and now my nRF52840DK is bricked...
