Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
Hello,
I am working on a project which requires 2 FTDs and 2 MTDs (Sensor and Actuator) in a Thread Network.
We are using nRF52840 dongle as FTDs and arduino nano sense...
after connect v3.7.1 programer v1.4.11 for a nrf9160dk I get an error "Error: Error occured when get library info. Errorcode: CouldNotOpenDevice (0x4) Lowlevel error: INVALID_OPERATION...
I have followed the tutorial of nRF5340: Network core bootloader to test the bootloader on app. core & net core.
I chose to use VS code to develop.
I am successful to...
Hi.
Simcom SIM7000 series datasheet recommends the following schematic:
Simcoms SIM800C module datasheet recommends the following schematic:
Quectel BG96 module...
I currently use an NRF52810 to write a firmware in an external flash, then an STM32 will read this firmware and download it in its internal flash. The communication between...
Hello,
I tried to read the value from bq4050 on smbus.
I had good results but I got wrong value randomly as following.
The last marked value is temperature from DAStatus2Reg...
Hello, I am developing a custom firmware for NRF52832 controller. I have develop power saving mode using power manage function. Also I have enabled interrupt inside code and...
hi,In SAADC sampling, the upper limit and lower limit of sampling results are set. Interrupt events are generated only when they are less than the lower limit or greater than...
Hey Devzone
Running into an interesting issue with the .zip files on http://developer.nordicsemi.com/.pc-tools/toolchain/ . When I try to download in browser they fail....
Hi
I am using nrf51422 (on the DK) with S130, SDK12, functioning as a central, reading multiple peripherals (which I also programmed),
Some of those peripherals have manufacturer...
Hello, With reference to Case ID: 278209, I wanted to include a driver file, for which I was suggested to add the label/variable "zephyr_library_include_directories(.)" in...
Hi,
I have a strange problem.
When I connect the jlink and battery power on board at the same time,and download the application, it works normally. But when I disconnect...
Good morning.
I have a custom board with softdevice 132 and sdk 15.0.3 where I have configured pin P0.16 and P0.17 for uart (rx, tx). I have read in other posts/problems...
I have written BTLE code that works on the nRF52840 DK using SoftDevice s140. I have ported this code to work on the nRF51 DK and nrf51822 MCU using SoftDevice s130. I use...
