I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hi,
I am testing the nRF9160 DK and used the asset tracker application with the IBasis SIM. Application works fine under CAT M1 network (IBasis SIM is roaming on o2/Telefonica...
Hello
We want modify mcuboot_primary and mcuboot_secondary partition.
mcuboot_primary end_address change to 0x70000 and size change to 0x60000.
mcuboot_secondary end_address...
Hello,
I'm trying to use MQTT API to get the information about connected/disconnected devices.
I'm subscribed to the topic: xyz/a/connections and I'm able to receive connection...
Hello,
I am trying to use the HID Keyboard Demo (ble_HID_keyboard_template from arduino sdk) . I'm using a RedBearLabs Blend Arduino with the nrF8001.
It works great...
Hi ,
I have been working on an example code in SDK : nRF5_SDK_17.0.2_d674dde\examples\ble_central_and_peripheral\experimental\ble_app_multirole_lesc\pca10040\s132\ses\ ...
Hi, On our new type of 9160 based boards, we failed to create a connection with TLS socket. After creating a TLS socket Without peer verification, and trying to connect with...
Hello,
Is it possible to use the nRF5 SDK v15.0.0 and nRF Connect SW to perform DFU upgrades? Are there any compatibility issues?
Is it advisable to continue using nRF5...
Hi,
I have purchased a ESIM from https://www.taisys.com/ , which works with DUAL Profile or Two networks.
We need to enable SIM TOOL KIT (STK) for enabling the sim...
Hi Guys,
I want to use nRF52840 Dongle as "BLE central UART".
In the first step, i used a nRF52840 Dongle with a Bluetooth low Enegy app in a nRFConnet, the result is...
Excuse me:
I can't find a api to close WDT，When the chip enters idle mode, the watchdog will reset the chip，I tried to call the command in the diagram below to turn off...
Hello,
I'm using nRF52832 board and I want to use it as a controller with a third party cellular modem to connect to AWS IoT. i.e. I want to send AT commands with the UART...
Hi,
I am trying to minimize the power consumption on a NRF52840.
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/optimizing-power-on-nrf52-designs states...
