Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I am using a STlink to flash a nrf51822 module , and i am using Keil to do that, i flashed the module but when i am scanning it to find it in my mobile i cant find it, i doesn...
Hi ,
Does the Application update depend on bootloader version? . I changed the boot loader but application remains same on my device , hence the device is not booting up...
I have an application with three other tasks beside the sdh task. I'm trying to integrate softdevice to my existing freertos application, but soon after the task scheduler...
Hi,
What would be the procedure for updating the firmware of device through another host micro controller UART? (Not with PC tools like nrf go studio, nrf connect, nrf jprog...
Sir,
I have a MDBT50Q-UFL evaluation board. I am using Keil uVision 5 and flashing is done through ST-Link. I downloaded the example files from http://developer.nordicsemi...
Hi,
I have Ublox EVK-NINA-B3 on table, which has totally different pin layout than NRF52 DK (not sure why): https://www.u-blox.com/sites/default/files/EVK-NINA-B3_UserGuide_...
Hello everyone! I am a beginner and I need help in understanding advertising data. I am migrationg from SDK 13 to SDK 15.2. In SDK 13, the advertising data with manufacturer...
Dear Engineer,
work on sdk15.2, pca10040 eavl board. one as central run this code
\nRF5_SDK_15.2.0_9412b96\nRF5_SDK_15.2.0_9412b96\examples\ble_central\ble_app_multilink_central...
I am starter developer of nRF51822 custom board.
in this board 16 mhz crystal is connected externally with XC1 and XC2 pins(37 & 38)
nRF5_SDK_12.1.0_0d23e2a rar file is...
Hello everyone,
I know that there are many similiar questions on the DevZone but i am not able to get it work and i dont uderstand it yet.
For example: https://devzone...
(Mesh_v2.11, SDK_15.0.0, NRF52832)
Hello,
I wonder if a device can relay DFU packets even though mesh_relay is disabled by nrf_mesh_opt_set(NRF_MESH_OPT_NET_RELAY_ENABLE...
I am trying to set up the nrf52840 dongle on IAR using an I-jet for debugging. I have iar version 8.32.1. I am using example project ble_app_blinky from the ble_peripheral...
Hi I met a problem during programming a combo of HID on nrf52. I have set combo HID that have keyboard and multi touch. after pairing my smartphone(galaxy note 8), keyboard...
Dear Colleagues,
I'd appreciate your advice on the selecting external or internal pullup or pulldown design for a wake up button which would cause minimal increase in current...
Hi.
I'm trying to make a bluetooth based sip/puff controller for disabled people. The main use case will be to enable people that can't use their hands, but move their head...
