Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
I am using the nRF54L15 (PANB511 Module ) controller with an ST7789V-based display connected via SPI21 at 8 MHz. Image bin files are stored using LittleFS in external flash...
Hi,
I'm trying to modify the Nordic sample apps included in the ESL Getting Started kit so that the tags first scan for Access Points (APs) so that they can connect to the...
Our IoT device is connecting to 2 different cell towers on the same carrier. Cell tower 'A' has signal of -90dBm, tower 'B' has signal of -105dBm.
The device is mainly attempting...
Hi,
I am using nRF54L15 with SDK v3.0.2 . I am facing an issue while initializing the LSM6DS3 sensor on a custom PCB.
Device Initialization Code:
#define...
I am developing a modbus server application for nrf54L15 in nrf sdk v3.2.3. But I ran into an issue where using MODBUS_MODE_ASCII requires UART_CFG_DATA_BITS_7. The modbus...
Dear Nordic,
The west build system is not acceptable for firmware development.
Firmware != Software. When we create firmware for a product, it must last for years. We...
Hi,
I've reliably implemented a Software Serial library on the nRF52832 using GPIOTE and nrf_delay_us to sample the 8 bits. I tried making this work more efficiently using...
Hi
Is it possible to use the 54dk for programming of our new board with the nRF54L15 running on 1.8V?
Is the voltage configurable on the 54 dk?
Best regards
Peer
I am using nRF Connect SDK (NCS) v2.9.0 for a Matter project.
Currently, the Manual Pairing Code generated is 21 digits long. I need to change this output to be 11 digits...
We follow the youtube video: www.youtube.com/watch
to add battery charging and fuel gauging to our nRF52832 Series project.
It works, but after we enable
CONFIG_PM_DEVICE...
Hi nordic team
I am working with the Nordic nRF5340 SoC using Zephyr RTOS .
Hardware
External QSPI flash:
MX25R6435F
QSPI configuration (DeviceTree):
...
Hardware: nRF9151 DK Modem firmware: mfw_nrf91x1_2.0.4 Carrier: Verizon (PLMN 311480), Band 13 Antenna: External Problem The modem continuously reselects between two cells...
Hi Nordic team,
In the context of adapting the software for our custom PCB I need to make some changes in some devicetree nodes for the net core. Therefore I wanted to add...
