Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice , like this:
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
After clicking on ACTIVATE SIM and having correctly filled in the SIM IICD and PUNK I am receiving the following message: Request failed with status code 503 What does this...
Hello,
Using scan sample I am trying to read drone Remote-ID. When broadcasting Remote ID via Wi-fi Beacon no problems occur, but once selecting only Wi-Fi NAN as delivery...
Hey! I'm working on a LE Audio project utilizing the nRF5340, where I need to stream audio both from and to the nRF and I have encountered the error "sw_codec_lc3: LC3 enc_bitrate...
Hello,
I can see there are some ADC examples on Github https://github.com/NordicPlayground/nRF52-ADC-examples But those examples are nRF SDK5. Are there any ADC examples...
Hello everyone,
I have a problem using pstorage_update. Normally it does as it should, but once i call ble_stack_init(); on my code, pstorage_update doesn't work anymore...
Hey,
I am trying to use the example for Sync_Advertising_conn to get a connection between 2 nrf5340 devices. but I get this message
the problem is in the config
CONFIG_BT_PER_ADV_SYNC_RSP...
Hello,
I am using the nRF52811 on a keyfob that transmits short packets when a button is pressed. The button directly connects power to the MCU, and the firmware immediately...
Hi,
I've just received my new nRF9161 Development Kit, but when going through the Quick Start, it fails to program.
Log:
2024-06-19T20:51:59.582Z INFO Initialising...
I am trying to interface nrf52833 devkit with BG95 devkit using PPP connection. For this I am using gsm_modem sample code. But when I am getting error while build configuration...
Hi,
We are wondering the current consumption in our custom board. The board has the following components (my FW view :)
nRF9160 - powered directly from batteries (either...
Hi
I use nRF7002-DK and sdk version as v2.5.2,download lesson8 exercise 3 solution and build was error as below log, which parts am I miss?
build config as below
...
Hello,
I a working on a project that uses the nRF5340 CCM peripheral (Network core) in an asynchronous mode. That is, I encrypt PDUs prior to scheduling them for transmission...
I want to configure my setup for secure boot and enable TFM and encrypted application images for firmware update. I am using nRF sdk version 2.5.0. My board is nRF9160. Now...
I have setup the UART along the same lines as the sample project in the DevZone Academy. I have extended the example provided to suit the project needs.
What I am getting...
In our custom board nrf5340-nrf7002, tried system_off(C:\ncs\v2.6.1\zephyr\samples\board\nrf )sample to check power consumption.
But it measures 0.60mA Is there any config...